Kobelco SK235SR-2 Operation Manual Download Page 221

Page: 221 / 308

Wear the proper safety equipment when working

around hot areas. Do not change oils, engine

coolant or filters immediately after machine has

been stopped.

Allow machine to cool down before performing

maintenance procedures.

４

4.15

500 HOUR INSPECTION & MAINTENANCE PROCEDURES

Thoroughly read and understand the "1.SAFETY PRECAUTIONS" of this MANUAL before operating or

servicing the machine.

Perform together with daily, 50-hour, 120-hour and 250-hour inspection and maintenance.

REPLACING ENGINE OIL AND ENGINE OIL FILTER

Do not touch the heated section during operation or immediately after being stopped. There is a

hazard of scalding.

Do not touch the heated section.

-Check the waste oil. If there are metal chips or powder mixed in the oil, contact KOBELCO distributor.

-Replace it at 50 hours operation for the first use of new machine.

-Replace engine oil filter simultaneously with the engine oil change.

［

4. MAINTENANCE

］

4-53

Summary of Contents for SK235SR-2



























































































































































































































































































Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands

Kobelco SK235SR-2, Operation Manual

Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands