Kobelco SK235SR-2 Operation Manual Download Page 68

Page: 68 / 308

This indicates the temperature of the engine

coolant water, and operates when the starter

key switch is turned to the "ON" position. The

temperature is normal in the white range. If

the indicator enters the red range, let the

engine low idle until the water cools down and

the indicator moves back into the white range.

This indicates the amount of fuel. F : Full tank

is about 330 L {87 gal} This gauge indicates

the remaining volume of fuel in the fuel tank.

Refuel when the indicator is approaching to

the "E" point. Refill the fuel tank with diesel

fuel only.

For fuel in use, see "4.3 LUBRICANT, FUEL

& COOLANT SPECIFICATIONS".

1. WHITE: Operating zone

2. RED: Refill

After starting engine, main screen (1) for

operator shown in the figure is usually

displayed.

METERS

COOLANT TEMPERATURE METER

RED: Maybe overheated

WHITE: Operating condition

BLUE: Cold condition, warm up engine and hydraulic oil

FUEL METER

SWITCH PANELS

［

2. MACHINE FAMILIARIZATION

］

2-6

Summary of Contents for SK235SR-2



























































































































































































































































































Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands

Kobelco SK235SR-2, Operation Manual

Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands