Kobelco SK235SR-2 Operation Manual Download Page 82

Page: 82 / 308

Main Screen Display for Operator

Display in Accordance with Switch Operation

Warning Display

Nibbler and Breaker Mode Display

Display for Maintenance

After starting engine, usually clock is displayed.

LCD MULTI-DISPLAY

When the warning is displayed on the multi-display, stop the work immediately and check failure cause

and service the trouble.

For checking and service, refer to the section of "Maintenance".

The gauge cluster processes signals received from various sensors and switches and outputs the

signals to LCD display and lamp display, and makes the buzzer sound.

The everyday check should be carried out according to not only the display on the multi-display but

also the instructions in section "Maintenance".

LCD display function is roughly divided into the following 5 types.

LCD (Liquid Crystal Display)

C.1 MAIN SCREEN

［

2. MACHINE FAMILIARIZATION

］

2-20

Summary of Contents for SK235SR-2



























































































































































































































































































Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands

Kobelco SK235SR-2, Operation Manual

Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands