Kobelco SK235SR-2 Operation Manual Download Page 216

Page: 216 / 308

Cleaning recirculate and fresh air filters

Recirculate air filter : Every 500 hours

Fresh air filter : Every 250 hours

Replacing inside and outside air filters

Recirculation air filter : After cleaning about 10

times

Fresh air filter : After cleaning about 10 times

Catch cover (1) on the left rear side of

operator seat and pull it this side.

Catch handle grip of fresh air filter (2)

through opening from which cover (1) is

removed and pull it out upward.

Air-Conditioner Filters Service

The flying debris due to compressed air may cause accident resulting in injury or death.

Wear safety goggles and respirator when cleaning the filters of air-conditioner.

The maintenance time shows the reference value. Clean them earlier than the specified time in case

where being used in dusty area.

E.1 Removing Fresh Air Filter

［

4. MAINTENANCE

］

4-48

Summary of Contents for SK235SR-2



























































































































































































































































































Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands

Kobelco SK235SR-2, Operation Manual

Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands