Kobelco SK235SR-2 Operation Manual Download Page 243

Page: 243 / 308

If the grease is white due to moisture content,

and the viscosity of grease is lowered, replace

the grease with a new one. Also, if the grease

is contaminated with a large amount of water,

replace the grease. In that case, contact our

dealer/distributor.

Loosen bolt (1) on the front side of upper

structure and remove cover (2) and packing

(3) for checking.

After checking bearing gear, replace

packing (3) with new one. After cleaning,

apply Loctite #572 for prevention from water

intruding.

Grease may be cloudy due to slight

contamination of water, but there is no

malfunction if the viscosity is high. When

water is there, loosen bolts (4) and spring

washers (5) on the lower side of lower

frame, remove cover (6) and packing (7)

and drain water.

４

Checking Swing Bearing Teeth

The deterioration of grease may cause damage of pinion shaft and swing bearing of swing reduction

unit.

［

4. MAINTENANCE

］

4-75

Summary of Contents for SK235SR-2



























































































































































































































































































Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands

Kobelco SK235SR-2, Operation Manual

Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands