Kobelco SK235SR-2 Operation Manual Download Page 141

Page: 141 / 308

Check leak for oil and water around the

engine.

Check that warnings of battery charge and

engine hydraulic pressure are disappeared,

and the readings of engine coolant

temperature meter (1) and fuel level meter

(2) are correct.

Check that exhaust sound and exhaust

color and vibration are normal.

３

B. Checking Function of Engine and Multi-Display

When warning was displayed on the multi-display, stop the engine immediately and investigate the

cause of error.

-Check the exhaust gas color (After warming-up and at no-load)

Colorless or light blue : Normal

Black : Abnormal, incomplete combustion

White : Abnormal, oil combustion due to oil loss by way of piston ring or valve guides

-Due to cold weather in winter the smoke may appear white. Be careful not to get confused.

［

3. MACHINE OPERATION

］

3-19

Summary of Contents for SK235SR-2



























































































































































































































































































Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands

Kobelco SK235SR-2, Operation Manual

Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands