manualshive.com logo in svg

Kinova Gen3, User Manual

Share
Download
Kinova Gen3 User Manual Download Page 68

KINOVA

®

 

Gen3 Ultra lightweight robot 

User Guide

68

 Accessing Vision module color and depth streams

This section describes access to the video module color and depth streams.

The video module sensors capture two video streams:

• color
• depth

The data from these streams is sent from the vision module back to the base controller via the
vision / expansion channel carried over the internal flex cable links.

These two streams are accessible via the Real Time Streaming Protocol (RTSP) on a computer
connected to the robot (with transport over real-time transport protocol (RTP)).

Using the default IP address settings for the base controller, the two streams are accessible via:

• color sensor stream: 

rtsp://<base IPv4 address>/color

• depth sensor stream: 

rtsp://<base IPv4 address>/depth

For the default configuration of the base controller network interface, this would give:

•

rtsp://192.168.1.10/color

•

rtsp://192.168.1.10/depth

Note: 

 Examples in the documentation will use the default base controller IP setting for

simplicity.

Streams specifications

• pixel format: Z16 pixel format - 16 bits LSB transferred as grayscale
• H.264 baseline profile (constant bitrate)
• RTSP server listening on port 554 (default)
• maximum of two simultaneous connections per stream
• inactivity timeout of 30 seconds

The KINOVA

®

 KORTEX™ Developer Guide section of the user guide describes in more detail

how to work with the vision module camera streams.

Summary of Contents for Gen3





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands