Keysight Technologies U3047AE04 User'S And Service Manual Download Page 57

Page: 57 / 81

User’s and Service Guide U3047-90002

U3047AE04

Service Information

The following replaceable parts may be ordered by sending an e-mail request to

[email protected]

. Be sure to include test set model, options and

serial number. Some parts may have long lead times.

Table 1

Replaceable Parts (E04)

Description

Keysight Part

Number

RF Cable, Semi-rigid

U3047-20016

RF Cable, Semi-rigid

U3047-20017

SW Interface Board, programmed

U3047-63018

2.4mm Female Short

85056-60021

Dress Nut (couplers)

N5230-20081

PNA-X Test Set Rear Lock Feet (right)

N5242-20138

PNA-X Test Set Rear Lock Feet (left)

N5242-20139

Front Panel LED Board

N5261-60005

Test Set Control Board (programmed)

N5261-60006

Screw-Pan Head Machine with thread patch,
Torx-T15 M3.5 with 0.6 thread, 12 mm-LG

0515-2317

U3047AE04 User’s and Service Guide

U3047-90002

DUT Control Board

U3020

63223

Switch, Solid State SP2T (70 GHz terminated)

5087-7317

Summary of Contents for U3047AE04


















































































Search results

Summary of Contents for U3047AE04

Reviews:

Related manuals for U3047AE04

Brands by name

Popular brands

Keysight Technologies U3047AE04, User'S And Service Manual

Search results

Summary of Contents for U3047AE04

Reviews:

Related manuals for U3047AE04

Brands by name

Popular brands