Keysight Technologies U3047AE04 User'S And Service Manual Download Page 35

Page: 35 / 81

User’s and Service Guide U3047-90002

U3047AE04

Controlling the U3047AE04 with N5247A

How to Access Interface Control Mode

1. To access the Interface Control mode, select Trace/Chan > Channel > Hardware Setup

Interface Control in the drop-down menu, and select Enable Interface Control.

The PNA-X Series Network Analyzer includes the Interface Control

application and rear panel connection. Please review this application before

connecting the Test Set to the PNA-X. Information regarding this

application can be found in the PNA-X Help menu, Interface Control. The

application is shown below.

Using Interface Control Mode
An Instrument Preset will reset all of the fields to their default settings.

If an error is encountered when sending Interface Control data, an error

message is displayed on the PNA-X screen and the Channel Trigger State

is set to Hold. You must fix the condition that caused the error, then change

the Channel Trigger State to its original setting

Summary of Contents for U3047AE04


















































































Search results

Summary of Contents for U3047AE04

Reviews:

Related manuals for U3047AE04

Brands by name

Popular brands

Keysight Technologies U3047AE04, User'S And Service Manual

Search results

Summary of Contents for U3047AE04

Reviews:

Related manuals for U3047AE04

Brands by name

Popular brands