background image

6

of    9

K2 SpeedPorter Installation

Depending on ballast size, position each SpeedPorter with 
the appropriate distance and insert the ballast. 

Required material: K2 SpeedPorter

Ballasting with K2 Porter:

The L-Profiles are fastened to the rails with the screws and 
M K2 slot nut included in the set. Torque: 16 Nm. The 
spacing of the L-Profiles depends on the number of bricks 
used. The Porters can be positioned both centrally to the 
Dome 1000, or laterally to the middle Dome.

Warning: K2 Porters must be mounted so that all base 
profiles within a module block are connected.

Materials required: K2 Porter, M K2, bolts with serrated 
under head M8x20

BALLASTING THE SYSTEM

Weighted down with ballast using bricks or slabs. Please 
follow the guidelines listed on the ballast weight table on 
page 16.  

Ballasting without additional item(s):

If only light ballasting up to 5 kg is required, insert one brick 
directly into the hollow chamber of the Dome S1000.

Ballasting with K2 Short Porter:

The L-Profiles are fastened to the rails with the screws and 
M K2 slot nut included in the set. Torque: 16 Nm. The 
spacing of the L-Profiles depends on the amount of bricks 
used 

Materials required: K2 Short Porter, M K2, hexagon socket 
countersunk head screw M8x20

15 | 20

Installation of S-Dome System

Summary of Contents for S-DOME SYSTEM





















Reviews: