67
GEN04
Chapter 16 - Service and Repair
Repair Strategy
•
Thorough knowledge of the H
ARMONIC
™ Generator 300 System User Manual and this manual is
mandatory prior to attempting any repair.
•
Loaner units may be provided free of charge for units which are being repaired under warranty.
•
Calibration is not covered by any warranty. There will be a nominal charge for the manufacturer to
perform the Calibration Procedure.
•
Only those replacement parts designated in the Spare Parts List below are available for sale.
•
Use only Ethicon Endo-Surgery approved replacement parts. Your Ethicon Endo-Surgery represen-
tative will be happy to assist you in obtaining replacement parts.
•
Replacement parts can be purchased from Ethicon Endo-Surgery by calling 1-800-USE-ENDO (U.S.
Customers) or by contacting an Ethicon Endo-Surgery representative (outside the U.S.).
Spare Parts List
Below is a list of spare parts which can be ordered through Ethicon Endo-Surgery for the H
ARMONIC
™ Generator 300 System.
The reference numbers below correspond to reference numbers on the Main Assembly Drawing in Appendix B of this manual.
Reference No.
Part No.
Description
1
D06358P01
Fuse Label
2
D06363P01
Back Panel Label
3
3583.036
Bezel Sub-Assembly
4
3583.180
Cover Enclosure
5
3583.053
Cable Assembly, Hand Piece Receptacle
6
3583.060
Cable Assembly, Earth Terminal – Chassis
7
3583.061
Cable Assembly, Power Entry – Chassis
8
3583.062
Cable Assembly, Fuse Holder – AC Switch
9
3583.064
Cable Assembly, Volume Control – Generator Board
10
3583.065
Cable Assembly, Fan with Cable Assembly
11
3583.066
Cable Assembly, Speaker with Cable Assembly
12
3583.067
Cable Assembly, Power Supply – Generator Board
13
3583.070
Cable Assembly, Power Entry – Fuse Holder
14
3583.073
Cable Assembly, Foot Switch - Generator Board
15
3583.079
LCD Display PCB
16
3583.112
Wire Assembly, AC Switch – Power Supply
17
900-000526
Power Cord, 13 Amps, 125 Volts, 15 feet
18
3583.125
Label, Tamper Evident
19
600-000234
Power-on Rocker Switch
20
620-000243
Fuse 3.15 Amps, 250 Volts, Slo-Blo
21
640-000268
Ferrite Clamp/Bracket 279 @100MHz
22
700-001493
Hardware, Nut 8-32 (for fan assembly)
23
700-000394-2
Hardware, Phillips 8 – 32 x 5/16
(for ground to chassis)
24
700-000504-1
Hardware, Phillips 4 – 40 x 3/8
25
700-000884
Hardware, KNut 4-40
26
700-001497
Hardware, Ground Pin
27
700-001653
Hardware, Knob
28
700-001662
Hardware, Feet, Rubber Black, with screw
29
700-001663
Hardware, Fuseholder, 5 x 20 PNL MNT
30
953-45A067
Hardware, Phillips 8 – 32 x 5/16
31
700-001665
Hardware, Phillips 8 – 32 x 1-1/4 (for fan assembly)
Summary of Contents for ETHICON ENDO-SURGERY HARMONIC 300
