JetCat P1000-PRO Operating Instructions Manual Download Page 48

Page: 48 / 70

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

Troubleshooting

Most frequent errors. Cause and remedy:

Problem

Cause

Remedy

Turbine doesn't ignite

Fuel supply lines are empty or not purged

ECU battery weak or empty

The kero start igniter failed. The
automatic glow plug test may not detect
a failed igniter!

Purge fuel system. Use the Test Functions
Menu, Purge Pump

Charge ECU battery

This is an extremely rare event but the
engine must be returned to

JetCat

. It may

be possible on some engine types to use
a temporary external plug. Call

JetCat

for

information.

Starting process fails

Turbine is still too warm;
Cool Down not yet completed.

Low battery or faulty connection.

Glow plug defective (red

Pump

running

LED blinks).

Three-conductor cable for starter motor
and glow plug disconnected.

Wait until

SlowDown

sequence is

finished.  The green OK LED will stop
blinking.

Charge battery.  Check ECU’s battery
connection.

Replace defective glow plug.

Check cable.  Check for proper
connection from ECU to the engine.

ECU doesn't follow full

commands from the
throttle stick

Programming alteration in R/C

transmitter

Check alignment with RC-Check menu.

Re-align ECU to the R/C system.

Turbine ignites, but the
start process is

discontinued.

Air in fuel feed lines.

Fuel pump not running.

Air leaks in fuel system. Examine all Festo
fittings, nipples, clunk, filter, etc.

Check for fuel filter clogs.

Test the pump in Test Functions menu,
(as soon as the red

Pump running

LED

illuminates, the fuel pump must run!).

Starter unit slips, makes
noise.

Dust and oil sediment on the compressor
nut and O-ring.

Clean O-ring and compressor nut
periodically, with cotton swab and
solvent.

EGT giving erratic
temperature or RPM
readings.

Transmitter antenna too close to the
model.

Keep the antenna away from the model.
It may cause false readings.

Turbine quits with
Watchdog Failure

Static discharge reset the ECU.

Do not mount ECU directly to the
fiberglass body of the plane. Use a

plywood mount with a layer of foam tape
and Velcro between the body and the
ECU. If the plane has a glossy finish and

the failure happened directly after the

Summary of Contents for P1000-PRO







































































Search results

Summary of Contents for P1000-PRO

Reviews:

Related manuals for P1000-PRO

Brands by name

Popular brands

JetCat P1000-PRO, Operating Instructions Manual

Search results

Summary of Contents for P1000-PRO

Reviews:

Related manuals for P1000-PRO

Brands by name

Popular brands