JetCat P1000-PRO Operating Instructions Manual Download Page 56 | Manualshive

Page: 56 / 70

background image

M

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

56

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

The LIMITs Menu

The LIMITs menu allows the operator to adjust the following parameters of the engine, within the allowable values,
according to the performance requirements of a particular model.

Value

Explanation

Minimum RPM

Turbine idle speed (If

IdleRPM-SET

or

Idle&Ramp-Set

is enabled by

Barom.Auto Tune

it

will further appear

(Auto)

in the display and

the RPM is set by ECU)

Maximum RPM

F

Turbine maximum speed

Indicate the thrust at full throttle. By varying the RPM this value calls the related thrust
of the engine. This provides a save and easy way to limit the maximum thrust.

Lowidle RPM

Reduced idle speed. This function is activated if the throttle stick is in idle and the
throttle trim is set to half. The Idle speed will be decreased to the programmed value.
The acceleration time to get back to the common idle speed can take 2-5 seconds
according the used engine type.

Ignition-Mode

Version of ignition type:
Kerosene-N JetCat kerosene start.
This parameter is for informational purposes only and can’t be changed

Battery Type

Kind of connected Battery:

NiCd

LiPo 2Cell/7.4V
LiPo3Cell/11.1V

(recommend by JetCat for PRO engines!!!)

LiFePo 3Cell/9,9V

Pb

(12V lead battery)

Barom.Auto Tune

Enables the ECU to align the control system according the barometric pressure. The
possible settings are:

Disabled:

No auto tuning by ECU

IdleRPM-Set:

Optimize of idle RPM only

Ramp-Set:

Optimize of acceleration only

Idle&Ramp-Set:

IdleRPM and acceleration are optimized

Smoker Flow

Only available when a bus-smoke pump is connected.
The smoke flow can be adjusted in a range of 0-100%.

Additional is shown the quantity of flow in milliliters (ml).

Fueltank size

Actual capacity of the fuel tank in ml

LowFuel Limit

Fuel level (ml) to activate the fuel warning function.

Telemetry

Select type of telemetry protocol, only applicable in conjunction with PRO-Interface
Options are (see also instruction manual of “JetCat telemetry adapter”):



NOT USED



Futaba SBUS-2



Graupner HOTT



MPX M-Link1



Jeti



MPX M-Link2

«
...
54
55
56
57
58
...
»

Summary of Contents for P1000-PRO







































































Reviews:

No comments

Related manuals for P1000-PRO

Brand: BAFANG Pages: 4

Brand: Yamaha Pages: 7

Brand: Stihl Pages: 40

Brand: SOMFY Pages: 2

Brand: PCM Pages: 83

Brand: Küchenprofi Pages: 28

Brand: Orientalmotor Pages: 6

Brand: Tanaka Pages: 11

EM-PMI540-T4000

Brand: Danfoss Pages: 71

Brand: Yamaha Pages: 25

Brand: Yamaha Pages: 18

Brand: Yamaha Pages: 50

Brand: Yamaha Pages: 62

Brand: Yamaha Pages: 59

Brand: Yamaha Pages: 64

Brand: Yamaha Pages: 66

Brand: Yamaha Pages: 66

TRANSERVO SSC04

Brand: Yamaha Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands