JetCat P1000-PRO Operating Instructions Manual Download Page 13

Page: 13 / 70

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

Data connector (A)

The data connector of the engines provides all necessary control signals for engine control as well as power on.

15pin SUB-D male connector

FCT - A MOLEX COMPANY FL, Sub-D Connector, 15-pin, straight, male

RS -No.:

812-6359

Pin-Inserts:

Sub-D-contact, Series: FK20PL, Male, Crimp, 24 → 20 AWG FK20PL-08V

RS -No.:

812-6220

Description

Info

Suggested connection

GND

Signal Ground

Connect to ground/negative pole of
supply battery

Throttle PWM input

RC-PWM Signal (THR)

Connect to servo PWM signal (0,8-
2,2ms) if throttle control should be
made via PWM signal

CAN-L

CAN-BUS

GSU-Bus-D

GSU bus (do not use!)

TXD 3,3V (COM1)

Serial interface transmit line

RXD-Cross Check, COM2

Secondary serial interface receive
signal

AUX PWM input

RC-PWM Signal (AUX)

Safety Shutdown input /
engine “kill” signal.

Safety shut down input.

This is an input for additional flight
termination systems.
This input pin should not be used to
stop the engine under normal
conditions.

Needs to be connected to GND to
allow engine to run.
This signal is only present on P1000
engines or engines with ECU

hardware setup V2.0 or higher!

Connect this pin to GND to enable
internal valves and pump!
If left open, valves and pump are
disabled by septate hardware
circuitry! (



engine cannot run).

If disconnected during engine run,
engine will be shut down

immediately with GSU error
message: “Kill Sig”

Power On Signal (4-14V)

See note 1 below!

Apply a positive voltage to power up
ECU/engine

Connect to positive pole of power
supply, to switch on ECU/engine
system. If disconnected ECU is

turned off. See also page 29 Engine
Power ON/OFF

CAN-H

CAN-BUS

GSU-Bus-C

GSU-bus (do not use!)

RXD 3,3V (COM1)

Serial interface receive line

+5V out, max 200mA

+5V output to GSU

TXD-Cross Check, COM2

Secondary serial interface transmit
signal

Airspeed

0-2,5V Airspeed Sensor or Analog
input

Summary of Contents for P1000-PRO







































































Search results

Summary of Contents for P1000-PRO

Reviews:

Related manuals for P1000-PRO

Brands by name

Popular brands

JetCat P1000-PRO, Operating Instructions Manual

Search results

Summary of Contents for P1000-PRO

Reviews:

Related manuals for P1000-PRO

Brands by name

Popular brands