JetCat P1000-PRO Operating Instructions Manual Download Page 66

Page: 66 / 70

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

Firmware Update

JetCat PRO engines allow for online update of the ECU´s firmware.

For the update process a JetCat USB-adapter (USB to serial) is required.

First you need to install the “JetCat ECU-V12 Updater” program (for Windows PC)

To install the software, type the following in the address line of your Internet browser:

http://www.cat-ing.de/jetcat-hexfiles/JetCatUpdaterV12.htm

then follow installation steps….

After the utility program has installed you are ready for the following steps:

Connect JetCat USB interface adapter to the PC and GSU.

GSU must also be connected to the PRO-Interface.

Power on engine system

Summary of Contents for P1000-PRO







































































Search results

Summary of Contents for P1000-PRO

Reviews:

JetCat P1000-PRO, Operating Instructions Manual, Page: 66 / 70

Search results

Summary of Contents for P1000-PRO

Reviews: