JetCat P1000-PRO Operating Instructions Manual Download Page 54

Page: 54 / 70

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

The INFO Menu

Info menu displays the following information:

Value

Explanation

Rest Fuel

Remaining fuel in tank. Tank size can be entered using the

LIMITs

menu. Value is reset

every time the ECU is switched on (or can be reset manually by pressing the

Change

Value/Item

button on the GSU).

Fuel Flow ml/min

Actual fuel consumption in ml/min.

BattCnd

Ubattery

The condition of the battery is indicated in the upper line:

--OK--

!WEAK!

--EMPTY--

If the battery voltage is 1.1V/Cell or higher “

—OK--

“ will be displayed.

If the battery voltage drops under 1.1V/Cell, the display will read “

!WEAK!”

. Red

Standby/Manual

and green

LED’s will blink simultaneously (at a rate of twice

per second). Starting the engine is not possible, until the battery is recharged. If the

engine is already running and the battery warning function is enabled, the warning
function will be activated.

If the battery voltage drops under 1.0V/Cell “—

EMPTY--

”

is displayed. Starting the

engine is not possible until the battery is recharged. If the engine is running, it will

be immediately shut off, to avoid a malfunction of the ECU.

Current voltage of the battery. Displayed on bottom line.

Baro
Temp

Indicate the current barometric pressure.
Temperature indicator (C°) in range of ECU

Last Run Time

Last engine run time.

Last Fuel Count

Quantity of fuel consumed, during the last engine run.

Last-Off PmpVolt

Volts applied to the pump when it was switched off.

Last Off RPM

RPM of the engine, when it was switched off.

Last Off TEMP

Temperature of the engine, when it was switched off.

Last Off Cond

Last stored Off condition.

Last Max Temp

Maximum temperature during the last engine run

Last Min Temp

Minimum temperature during the last engine run

Last AVG Temp

Average temperature during the last engine run

Last MaxR AVGTmp

Average full throttle temperature during the last engine run

Last Max Pump

Maximum pump voltage during the last engine run

Last Min Pump

Minimum pump voltage during the last engine run

Last Avg Pump

Average pump voltage during the last engine run

Last Fail Safe Cnt

Number of Fail Safe during the last engine run

Last Fail Safe Time

Fail Safe Time in seconds

Last-Max AirSpd

Maximum reached flight speed during the last flight
(Only by connected Airspeed sensor!)

Summary of Contents for P1000-PRO







































































Search results

Summary of Contents for P1000-PRO

Reviews:

Related manuals for P1000-PRO

Brands by name

Popular brands

JetCat P1000-PRO, Operating Instructions Manual

Search results

Summary of Contents for P1000-PRO

Reviews:

Related manuals for P1000-PRO

Brands by name

Popular brands