JetCat P1000-PRO Operating Instructions Manual Download Page 12

Page: 12 / 70

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

Connections on the engine, overview

Once you have unpacked and identified all the components, follow the system diagram/photo for all connections.

Connector A
SUB-D 15pin connector data/control. Or
customer specific connector

Connector B
XT60-power connector. Or
customer specific connector

Fuel inlet, fuel pump is inside of engine!
Do not use a filter in the suction line just an UAT air
trap or large felt clunk.

Bleed air output port (OPTIONAL).
Can be used to pressurize fuel tank for high altitude
operation.
Inside of the engine there is a one-way valve fitted which

prevents reverse flow into the engine. If bleed air function
is not needed, please block this port by a piece of tubing

Expansion connector C
4-pin Molex connector.

For connection of GSU or
smoke pump or

other

JetCat accessory.

Summary of Contents for P1000-PRO







































































Search results

Summary of Contents for P1000-PRO

Reviews:

Related manuals for P1000-PRO

Brands by name

Popular brands

JetCat P1000-PRO, Operating Instructions Manual

Search results

Summary of Contents for P1000-PRO

Reviews:

Related manuals for P1000-PRO

Brands by name

Popular brands