JetCat P1000-PRO Operating Instructions Manual Download Page 51

Page: 51 / 70

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

Menu Structure

All similar data and running parameters are grouped in separate menus. Menus can be displayed, and their values

modified (where accessible), by using the GSU.

Menu Selections



RUN menu



MIN/MAX menu



RC-Check menu



INFO menu



STATISTICS menu



LIMITS menu



TEST menu

Selecting a Menu

The corresponding buttons (hot keys) can directly select the “Run”, “Info”, “MIN/MAX”, or “Limits” menus. An
alternate method is to press and hold the

Select Menu

button and use the

+ / -

buttons for selecting.

Note:

this

method is the only access to all menus.

Change Values / Items

To change an indicated value, press and hold the

Change Value/Item

button while using the

+ / -

buttons to alter its

value. An arrow (



) will appear in front of the value, if it can be changed.

Summary of Contents for P1000-PRO







































































Search results

Summary of Contents for P1000-PRO

Reviews:

Related manuals for P1000-PRO

Brands by name

Popular brands

JetCat P1000-PRO, Operating Instructions Manual

Search results

Summary of Contents for P1000-PRO

Reviews:

Related manuals for P1000-PRO

Brands by name

Popular brands