JetCat P1000-PRO Operating Instructions Manual Download Page 46

Page: 46 / 70

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

Once these conditions are met, engine proceeds to

Off

Speed Control

Speed Control mode -- only active when the air speed sensor is connected. Regulates model
flight speed.

Table 2

Code Value

Explanation

R/C Off

AUX switched to Off position or throttle stick and throttle trim moved to the
minimum position.

OverTemp

Turbine running over temperature. Exceeded high temperature parameter and time
out.

IgnTimOut

Turbine did not ignite within programmed time interval.

AccTimOut

Turbine achieved ignition but did not accelerate within programmed time interval.

Acc.Slow

Turbine achieved ignition, but acceleration was less than the programmed value,

during startup.

Over-RPM

Turbine exceeded the maximum RPM, by 5% and a delay of 0.5 seconds.

Low-RPM

Turbine running under the minimum RPM, by 10% and a delay of 3 seconds.
Usually triggered by a flame out.

BattryLow

Battery pack is dead. Cell voltage is < 1.0V.

Auto-Off

Turbine shut down via the AutoOff sequence, using the AUX channel.

LowTemp

EGT dropped below the minimum value. A dislodged EGT sensor can trigger this
shut down.

HiTempOff

EGT exceeded the maximum range (~950 °C).

GlowPlug!

Defective kero/glow plug.

WatchDog

ECU processor was locked out usually from static discharge or voltage spike in
power supply.

FailSafe

Turbine was shut down from a failsafe timeout condition.

ManualOff

Turbine was shut off by using the GSU.

PowerFail

The power failed to the ECU when the engine was running. This will occur if the
power was lost because of a defective battery, connection or if the switch is turned

off before the engine is shut-down.
Note: If this state is displayed the Info, Min/Max and Statistics menus retain
information from the previous run.

TempSensor Fail EGT sensor failed.

Note: This could happen only during startup.

FuelFail

Rpm2Fail

Second rpm sensor defective, only for 2-shaft engines

2nd EngF

Cross check enabled, and shut down was forced due to 2

engine shut down

2nd Diff

Cross check enabled, and shut down was forced due to thrust differential

2nd Comm

Cross check enabled, communication error to 2

engine.

Summary of Contents for P1000-PRO







































































Search results

Summary of Contents for P1000-PRO

Reviews:

Related manuals for P1000-PRO

Brands by name

Popular brands

JetCat P1000-PRO, Operating Instructions Manual

Search results

Summary of Contents for P1000-PRO

Reviews:

Related manuals for P1000-PRO

Brands by name

Popular brands