Jeep Patriot 2011 Owner'S Manual Download Page 200 | Manualshive

Page: 200 / 490

background image

The dual brake system provides a reserve braking capac-
ity in the event of a failure to a portion of the hydraulic
system. A leak in either half of the dual brake system is
indicated by the Brake Warning Light, which will turn on
when the brake fluid level in the master cylinder has
dropped below a specified level.

The light will remain on until the cause is corrected.

NOTE:

The light may flash momentarily during sharp

cornering maneuvers, which change fluid level condi-
tions. The vehicle should have service performed, and
the brake fluid level checked.

If brake failure is indicated, immediate repair is neces-
sary.

WARNING!

Driving a vehicle with the red brake light on is
dangerous. Part of the brake system may have failed.
It will take longer to stop the vehicle. You could have
a collision. Have the vehicle checked immediately.

Vehicles equipped with the Anti-Lock Brake System
(ABS), are also equipped with Electronic Brake Force
Distribution (EBD). In the event of an EBD failure, the
Brake Warning Light will turn on along with the ABS
Light. Immediate repair to the ABS system is required.

Operation of the Brake Warning Light can be checked by
turning the ignition switch from the OFF position to the
ON/RUN position. The light should illuminate for ap-
proximately two seconds. The light should then turn off
unless the parking brake is applied or a brake fault is
detected. If the light does not illuminate, have the light
inspected by an authorized dealer.

198

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
198
199
200
201
202
...
»

Summary of Contents for Patriot 2011











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Patriot 2011

2013 C-Class Coupe

Brand: Mercedes-Benz Pages: 388

Brand: Standby Pages: 10

Brand: Victory 4x4 Pages: 13

Brand: Subaru Pages: 34

Brand: Tessera4x4 Pages: 20

Brand: Whispbar Pages: 15

Brand: Toro Pages: 24

Brand: Volvo Pages: 10

LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...

Brand: Dakota Digital Pages: 3

Brand: ULTIMATE SPEED Pages: 50

Brand: Quadratec Pages: 12

Brand: r.LiNK Pages: 20

Brand: Lincoln Pages: 586

Brand: Prime Design Pages: 12

Brand: Belkin Pages: 30

Brand: Mitsubishi Pages: 141

Brand: Rola Pages: 2

DODGE AD100 1993

Brand: Chrysler Pages: 1502

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands