manualshive.com logo in svg

Jeep Patriot 2011, Owner'S Manual

The Jeep Patriot 2011 Owner's Manual is a comprehensive guide that allows you to maximize your vehicle's potential. This manual provides detailed instructions on maintenance, troubleshooting, and operating the Jeep Patriot 2011. Download it for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

General Information

This device complies with Part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions:

•

Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.

•

This device may not cause harmful interference.

•

This device must accept any interference received,
including interference that may cause undesired
operation.

VOICE COMMAND — IF EQUIPPED

Voice Command System Operation

This Voice Command system allows you to
control your AM, FM radio, satellite radio, disc
player, and a memo recorder.

NOTE:

Take care to speak into the Voice Interface

System as calmly and normally as possible. The ability of
the Voice Interface System to recognize user voice com-
mands may be negatively affected by rapid speaking or a
raised voice level.

WARNING!

Any voice commanded system should be used only
in safe driving conditions following local laws. All
attention should be kept on the roadway ahead.
Failure to do so may result in a collision causing
serious injury or death.

When you press the Voice Command

button, you

will hear a beep. The beep is your signal to give a
command.

128

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for Patriot 2011











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Patriot 2011

JETBAG 320 Fitting Instructions Manual preview
320
Brand: JETBAG Pages: 44
JASTEC von-S2 Instruction Manual preview
von-S2
Brand: JASTEC Pages: 12
Westin 23-3130 Instructions preview
23-3130
Brand: Westin Pages: 3
AMP Research BEDXTENDER HD MAX 74841-00A Assembly Installation Manual preview
BEDXTENDER HD MAX 74841-00A
Brand: AMP Research Pages: 9
Belkin F8V7058-APL User Manual preview
F8V7058-APL
Brand: Belkin Pages: 2
Kia Picanto Manual preview
Picanto
Brand: Kia Pages: 680
Honda 2006 Accord Owner'S Manual preview
2006 Accord
Brand: Honda Pages: 569
Kogan CERTA CTCVINCVR14A User Manual preview
CERTA CTCVINCVR14A
Brand: Kogan Pages: 4
Pet Gear TL9000 Instruction Manual preview
TL9000
Brand: Pet Gear Pages: 4
Suzuki IGNIS 2022 Series Manual preview
IGNIS 2022 Series
Brand: Suzuki Pages: 570
Mitsubishi MOTORS OUTLANDER PHEV 2022 Manual preview
OUTLANDER PHEV 2022
Brand: Mitsubishi MOTORS Pages: 8
wtw spectroFlex Car Adapter Operating Manual preview
spectroFlex Car Adapter
Brand: wtw Pages: 4
Metra Electronics 95-7617B Installation Instructions Manual preview
95-7617B
Brand: Metra Electronics Pages: 8
Cadillac 2000 Escalade Manual preview
2000 Escalade
Brand: Cadillac Pages: 339
Macally MAGME User Manual preview
MAGME
Brand: Macally Pages: 10
Quadratec QuadraTop Adventure Top 1113.00 Series Installation Manual preview
QuadraTop Adventure Top 1113.00 Series
Brand: Quadratec Pages: 20
TERAFLEX 1365000 Manual preview
1365000
Brand: TERAFLEX Pages: 18
RAM PROMASTER 2021 Owner'S Manual preview
PROMASTER 2021
Brand: RAM Pages: 288

Brands by name

Popular brands

Load more brands