Jeep Patriot 2011 Owner'S Manual Download | Manualshive

Page: 196 / 490

background image

INSTRUMENT CLUSTER DESCRIPTIONS

1. Fuel Gauge/Fuel Door Reminder

When the ignition switch is in the ON/RUN
position, the pointer will show the level of fuel
remaining in the fuel tank. The fuel pump
symbol points to the side of the vehicle where

the fuel door is located.

2. Charging System Light

This light shows the status of the electrical charg-
ing system. The light should come on when the

ignition switch is first turned to ON/RUN and remain on
briefly as a bulb check. If the light stays on or comes on
while driving, turn off some of the vehicle’s non-essential
electrical devices or increase engine speed (if at idle). If
the charging system light remains on, it means that the
vehicle is experiencing a problem with the charging
system. Obtain SERVICE IMMEDIATELY. See an autho-
rized dealer.

If jump starting is required, refer to “Jump Starting
Procedures” in “What To Do In Emergencies”.

3. Electronic Throttle Control (ETC) Light

This light informs you of a problem with the
Electronic Throttle Control (ETC) system. If a
problem is detected, the light will come on
while the engine is running. Cycle the ignition

key when the vehicle has completely stopped and the
shift lever is placed in the NEUTRAL position. The light
should turn off. If the light remains lit with the engine
running, your vehicle will usually be drivable; however,
see an authorized dealer for service as soon as possible. If
the light is flashing when the engine is running, imme-
diate service is required and you may experience reduced
performance, an elevated/rough idle or engine stall and
your vehicle may require towing. The light will come on
when the ignition is first turned to ON/RUN and remain

194

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
194
195
196
197
198
...
»

Summary of Contents for Patriot 2011











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Patriot 2011

Brand: AC Schnitzer Pages: 16

Brand: Calix Pages: 5

Brand: Prorack Pages: 14

BLADE-AL(TB)-TL2

Brand: iDataLink Pages: 9

Brand: Magneti Marelli Pages: 2

Brand: Atera Pages: 10

4500 CHASSIS CAB 2012

Brand: RAM Pages: 7

Brand: Broadfeet Pages: 2

OPTIA hybrid 2020

Brand: Kia Pages: 54

Stargazer Spirit XTR Skylight

Brand: Lippert Pages: 8

Brand: HAKR Pages: 9

Brand: Oldsmobile Pages: 276

Brand: Volkswagen Pages: 32

Brand: Porsche Pages: 146

Brand: Renault Pages: 11

Brand: Kuda-Phonebase Pages: 3

Brand: Curt Group Pages: 3

Brand: Juna Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands