manualshive.com logo in svg

Jeep Patriot 2011, Owner'S Manual

The Jeep Patriot 2011 Owner's Manual is a comprehensive guide that allows you to maximize your vehicle's potential. This manual provides detailed instructions on maintenance, troubleshooting, and operating the Jeep Patriot 2011. Download it for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

CAUTION!

Do not use a portable battery booster pack or any
other booster source with a system voltage greater
than 12 Volts or damage to the battery, starter motor,
alternator or electrical system may occur.

WARNING!

Do not attempt jump-starting if the battery is frozen.
It could rupture or explode and cause personal injury.

Preparations For Jump-Start

The battery in your vehicle is located in the front of the
engine compartment below the air intake duct. To access
the battery remove the air intake duct by turning the two
finger screws, located on the radiator support.

Air Intake Finger Screws

6

WHAT TO DO IN EMERGENCIES

389

Summary of Contents for Patriot 2011











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Patriot 2011

Garmin BC 30 Owner'S Manual preview
BC 30
Brand: Garmin Pages: 2
OEM Audio Reference Series Manual preview
Reference Series
Brand: OEM Audio Pages: 29
Wagan 2227-1 User Manual preview
2227-1
Brand: Wagan Pages: 8
Thermo King T- series Driver Manual To Simple Operation preview
T- series
Brand: Thermo King Pages: 2
SuperATV AAB-P-RZR900-K2-001 Installation Instructions preview
AAB-P-RZR900-K2-001
Brand: SuperATV Pages: 3
Ironton 44596 Owner'S Manual preview
44596
Brand: Ironton Pages: 7
V8 equipment EBEX.2 Instruction Manual preview
EBEX.2
Brand: V8 equipment Pages: 17
Maserati Quattroporte Automatic Owner'S Manual preview
Quattroporte Automatic
Brand: Maserati Pages: 272
Car-Systems Parktronic system Volkswagen Golf MK7 Assembly Manual preview
Parktronic system Volkswagen Golf MK7
Brand: Car-Systems Pages: 10
Warn 70948 Installation Instructions preview
70948
Brand: Warn Pages: 5
Sagem MyCK100 User Manual preview
MyCK100
Brand: Sagem Pages: 10
N-Com Bluetooth Kit3 PLUS User Instructions And Safety preview
Bluetooth Kit3 PLUS
Brand: N-Com Pages: 36
Cadillac STS 2011 Owner'S Manual preview
STS 2011
Brand: Cadillac Pages: 529
Toro 07389 Installation Instructions Manual preview
07389
Brand: Toro Pages: 16
Reliant ROBIN 850 Workshop Manual preview
ROBIN 850
Brand: Reliant Pages: 206
WABCO TEBS E Manual preview
TEBS E
Brand: WABCO Pages: 224
EUFAB 16559 Operating Instructions Manual preview
16559
Brand: EUFAB Pages: 12
Wallbox commander Installation Manual preview
commander
Brand: Wallbox Pages: 13

Brands by name

Popular brands

Load more brands