Jeep Patriot 2011 Owner'S Manual Download Page 446

Page: 446 / 490

At Each Oil Change

•

Change the engine oil filter.

•

Inspect the brake hoses and lines.

•

Check the manual transmission fluid level.

CAUTION!

Failure to perform the required maintenance items
may result in damage to the vehicle.

Required Maintenance Intervals

Refer to the Maintenance Schedules on the following
pages for the required maintenance intervals.

T
E

S
C

D
U

L
E

444

MAINTENANCE SCHEDULES

Summary of Contents for Patriot 2011











































































































































































































































































































































































































































































































Search results

Summary of Contents for Patriot 2011

Reviews:

Related manuals for Patriot 2011

Brands by name

Popular brands

Jeep Patriot 2011, Owner'S Manual

Search results

Summary of Contents for Patriot 2011

Reviews:

Related manuals for Patriot 2011

Brands by name

Popular brands