Jeep Patriot 2011 Owner'S Manual Download Page 438 | Manualshive

Page: 438 / 490

background image

BULB REPLACEMENT

Headlamps

1. Raise the hood and locate the connector behind the
headlamp.

2. Reach into engine compartment and pull red lock out
at connector.

3. Remove the green connector from the back of the bulb
by pulling straight back.

4. Twist the bulb to the left.

5. Pull bulb outward from assembly.

NOTE:

These are halogen bulbs. Take care not to touch

the bulb with your fingers. Body oils from your fingers
could cause excessive heat buildup which reduces bulb
life.

Fog Lamps

Refer to the Service Manual or see your authorized dealer
for bulb replacement.

CAUTION!

Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.

436

MAINTAINING YOUR VEHICLE

«
...
436
437
438
439
440
...
»

Summary of Contents for Patriot 2011











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Patriot 2011

Brand: Warrior Products Pages: 3

Brand: Dometic GROUP Pages: 20

Brand: DEFA Pages: 7

Brand: Prorack Pages: 15

Brand: Audi Pages: 9

Brand: Belkin Pages: 4

Brand: Cadillac Pages: 518

Brand: Opel Pages: 141

Brand: Motoalliance Pages: 8

Brand: Thule Pages: 4

Brand: Edelbrock Pages: 2

Brand: Mercedes-Benz Pages: 93

Brand: Volvo Pages: 18

Brand: Lexus Pages: 6

Brand: Curt Group Pages: 2

Brand: JBA Pages: 5

MagicWatch MWE150

Brand: Waeco Pages: 176

2018 GRAND CHEROKEE

Brand: Jeep Pages: 372

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands