18
IT - Dati technici
Voltaggio
6 - 8,4 V
Batterie
6 NiCd- / NiMH-Celle
2 S LiPo
Tensione BEC
6 V
Uso
RC-Car 1:10
Carico BEC
1,0 A
Protezione Sottotensione
Carico continuo
40 A
Dimensioni
~ 46,5 x 37 x 32 mm
Prova di spruzzi
GB - Technical Data:
Operating Voltage
6 - 8,4 V
Battery Pack
6 NiCd- / NiMH-Cells
2 S LiPo
BEC Voltage
6 V
Intended use
RC-Car 1:10
BEC Current
1,0 A
Protection Circuit
Under voltage cut off
Continuous load
40 A
Size
~ 46,5 x 37 x 32 mm
Splash proof
Attacco per la batteria
Battery connector
Cavo di allacciamento
del regolatore
Signal wire
Pulsante ON/OFF
On/Off switch
Installazione e Connessione
Piazzare il regolatore nella macchina, dove è protetto da umidità,
vibrazioni e urti. Provvedete inoltre che il regolatore sia sempre
raffreddato via aria. Per esempio: non avvolgetelo nella gomma-
piuma. Si consiglia di fi ssare il regolatore con un nastro biadesi-
vo. L´interruttore si consiglia di mettere a una parte protetta, ma
facilmente raggiungibile nello stesso momento. Rispettate semp-
re i consigli del Vostro fornitore.
Nel vostro modello RC è stato integrato il regolatore nr. 081468.
Questo regolatore possiede 2 pulsanti ON/OFF. Il Numero 1 ac-
cende o spegne il regolatore. Con il pulsante numero 2 si accen-
de o spegne il spegnimento automatico del limiti di sottotensione.
Se avete acquistato la versione Lipo del modello o se state usan-
do batteria al litio-polimero questo pulsante deve essere su ON.
Solo in questo modo la batteria Lipo e´protetta da una scarica
profonda e di eventuali danni relativi! A una soglia di 6 V tensione
complessiva il regolatore si spegne per non fare scaricare la
batteria in modo troppo profondo. Se invece avete acquistato la
versione NiMh del modello o usate una batteria Nimh, il pulsan-
te deve essere su OFF. Cosi il regolatore non si spegne a una
tensione di 6V, ma consente una scarica fi no ad una tensione
complessiva di ca. 4 V.
Collegate il regolatore con il motore tramite i spinotti oppure
saldate gli attacchi direttamente (se necessario). Accettarsi che
sono presenti una buona connessione a bassa impedenza e un
buon isolamento con una guaina termo ritraibile. Minimare la di-
stanza dei collegamenti tra motore e regolatore e tra batteria e
regolatore.
Prima collegare tutti i cavi e in seguito collegare il regolatore con
la ricevente. Collegare il cavo-servo con l´uscita della ricevente.
Installing and connecting
Position the ESC within the vehicle so that it will be protected
from moisture, vibration and impacts ensuring that suffi cient air
can circulate to cool the unit. Never wrap the ESC in foam, we
recommend mounting the unit to the vehicle using double sided
sticky tape and that the switch is located where it will be pro-
tected but is also easily accessible. Please refer to your models
instructions for advice of where to situate these components.
Your RC Model comes with the ESC 081468 installed. This regu-
lator has two On/off switches. Number 1 turns the regulator on
and off. Number 2 is for turning on / off the under-voltage cutoff.
If you have purchased the lipo version of your model or consider
to using a lithium polymer battery, this switch has to be set to
On. This function protects the lipo battery against deep discharge
and possible damage due to deep discharge! At a threshold volt-
age of 6 V total the esc switches autom. off to safe the battery
from under voltage. If you have purchased the NiMH version of
your model or consider to using a NiMh battery this switch has to
be set to Off. The controller allows a voltage less than 6 V down
to 4 V.
Use high quality connectors ensuring that all soldered joints are
sound and check for resistance. Alternatively, the cables may be
soldered directly to the motor connecting cables. In both cases
the joints must be well insulated using heat shrink tube to ensure
that a short circuit cannot occur and keep the cables as short as
possible.
Once the battery pack and motor are connected the servo cable
on the ESC can be plugged into the throttle output of the receiver.
Modalita´Lipo ON/OFF
Lipomode On/Off
Attacco per la motore
motor connector