Jadever JIF-2002 Manual Download Page 50

Page: 50 / 67

JIF-2002 WEIGHING INDICATOR&CONTROLLER

◎

Built-in Automatic Program Mode: Loss-in-Weight Batching

(F101=4)

SP1 – Supplying Bin

Gate

SP2 – Full Flow Gate

Free – Dribble Flow Gate

Start signal – Pin22

1. The Weighing Hopper is empty as is the Receiving Bin. The display shows

"0", and all Gates are closed.

2. Open the Supplying Bin Gate.

3. When the GROSS Weight reaches "

SP 1

", the

SP 1

Output (Pin 12) signal

will come

. Closed the Supplying Bin Gate by using the SP 1 Output ON

signal.

4. The displayed weight will exceed the SP 1 value by the Free Fall value.

This weight is not necessarily accurate - but accuracy is not needed at this

moment since the purpose of this event is to fill up the Weighing Hopper.

The SP 1 value is always compared to GROSS weight.

5. Input a TARE signal (Pin 24) to ZERO the display.

6. Input the Start signal via the Control I/O interface connector (Pin 22). When

the Start signal is received, the SP 2 and Free Outputs "come ON".

Note : When the Final Weight is 0, the Pin 11 and 10 are kept OFF .

7. Open the Full-Flow Gate and the Dribble-Flow Gate for Full-Flow filling into

the Receiving Bin.

Summary of Contents for JIF-2002




































































Search results

Summary of Contents for JIF-2002

Reviews:

Related manuals for JIF-2002

Brands by name

Popular brands

Jadever JIF-2002, Manual

Search results

Summary of Contents for JIF-2002

Reviews:

Related manuals for JIF-2002

Brands by name

Popular brands