Jadever JIF-2002 Manual Download Page 6

Page: 6 / 67

JIF-2002 WEIGHING INDICATOR&CONTROLLER

2-1 Best Conditions For Use

When installing and wire connecting on

JIF-2002

, please follow the

points and guide for preventing any abnormal situation occurred.

Before

connecting

the Electric Power Supply, please identify

the input Electric voltage type is AC 110V or AC 220V.

The Grounding Wire shall be properly connected .

The

Operation

Temperature shall range within 0

℃

~ 45

℃

please DO not install in any place of direct sun-light.

Due to the minute output signal from Load Cell, please use

isolated cables. Also, separate the Load Cell cable from the

power supply cable and control I/O cables.

The input power shall be AC 110V or AC 220V

10%, if the

Electric Power Supply is not stable or the interference signal

exists, that may cause uncertain actuation or reaction, even

damages .

Therefore, please utilize Electric Power Supply Stabilizer of

adequate capacity.

2-2 Power Supply Connecting

◎

Open the case, there is a jumper

﹝

﹞

near the transformer, please insert

a short-circuit pin to the available side.

Summary of Contents for JIF-2002




































































Search results

Summary of Contents for JIF-2002

Reviews:

Related manuals for JIF-2002

Brands by name

Popular brands

Jadever JIF-2002, Manual

Search results

Summary of Contents for JIF-2002

Reviews:

Related manuals for JIF-2002

Brands by name

Popular brands