Jadever JIF-2002 Manual Download Page 43

Page: 43 / 67

JIF-2002 WEIGHING INDICATOR&CONTROLLER

STEP 3:

The screen will show SP1, please press the

↵

key. The screen

will show a 6-digit value with blinking 0 000.000. Please use

the

key to change position and the

key to

change value. Please press the

↵

key to confirm SP1 value.

STEP 4:

The screen will show SP2, please press the

↵

key. The screen

will show 6-digit value with blinking 0 000.000. Please use the

key to change position and the

key to

change value. Please press the

↵

key to confirm SP2 value.

STEP 5 :

The screen will show Free, please press the

↵

key. The screen

will show 6-digit value with blinking 0 000.000. Please use the

key to change position and the

key to

change value. Please press the

↵

key to confirm Free Fall

value.

STEP 6:

The screen will show Hi, please press the

↵

key. The screen

will show 6-digit value with blinking 0 000.000. Please use the

key to change position and the

key to

change value. Please press the

↵

key to confirm Hi (Over

Limit) value.

STEP 7 :

The screen will show Lo, please press the

↵

key. The screen

will show 6-digit value with blinking 0 000.000. Please use the

key to change position and the

key to

change value. Please press the

↵

key to confirm Lo (Under

Limit) value.

STEP 8:

The screen will show CODE 00, please press the STANDBY

key to leave set point codes. If you wish to continue reset other

SET POINT CODES. Please enter values according to step1 to

step 8 again.

Summary of Contents for JIF-2002




































































Search results

Summary of Contents for JIF-2002

Reviews:

Related manuals for JIF-2002

Brands by name

Popular brands

Jadever JIF-2002, Manual

Search results

Summary of Contents for JIF-2002

Reviews:

Related manuals for JIF-2002

Brands by name

Popular brands