Jadever JIF-2002 Manual Download Page 48

Page: 48 / 67

JIF-2002 WEIGHING INDICATOR&CONTROLLER

◎

Built-in Automatic Program Mode: Normal Batching( F101 = 3 )

SP1 - Full Flow Gate

SP2 - Medium Flow Gate

Free - Dribble Flow Gate

Start signal – Pin22

1. The Weighing Hopper is empty, the display shows "0", and all Gates are

closed. If the display is not at ZERO,

input a TARE

signal (Pin 24) to

re-ZERO the display

2. Check if the Weighing Hopper is empty using the ZERO Band Output

(Pin 13).

3. Input the Start signal via the Control I/O Interface connector (Pin 22).

When the Start signal is received, then SP 1, SP 2, and Free Output

signals will "come ON".

Note: When the Final Weight is 0, the Pin 12, 11 and 10 are kept OFF.

4. Open the Supply Bin's: Full-Flow Gate, Medium-Flow Gate, and

Dribble-Flow Gate.

5. When the display reaches "

Final - SP 1

", the

SP 1

Output (Pin 12) signal

will come

OFF

. Closed the Full-Flow Gate by using the SP 1 Output OFF

signal.

6. When the display reaches "

Final - SP 2

", the

SP 2

Output (Pin 11) signal

will come

OFF

Closed the Medium-Flow Gate by using the SP 2 Output OFF signal.

Summary of Contents for JIF-2002




































































Search results

Summary of Contents for JIF-2002

Reviews:

Related manuals for JIF-2002

Brands by name

Popular brands

Jadever JIF-2002, Manual

Search results

Summary of Contents for JIF-2002

Reviews:

Related manuals for JIF-2002

Brands by name

Popular brands