iPECS eMG800 Hardware Description & Installation Manual Download Page 5

Page: 5 / 101

iPECS eMG800
Hardware Description and Installation Manual

Issue 1.8

Table of Contents

Introduction ................................................................................................... 1

1.1

Important Safety Instructions ................................................................................. 1

1.1.1

Safety Requirements .................................................................................................. 1

1.1.2

Precaution .................................................................................................................. 2

1.2

Manual Use ........................................................................................................... 3

System Overview .......................................................................................... 4

2.1

iPECS eMG800 System Highlights ........................................................................ 4

2.2

System Connection Diagram ................................................................................. 5

2.3

System Components ............................................................................................. 6

2.4

General Specifications ........................................................................................... 7

2.4.1

Dimension and Weight ............................................................................................... 7

2.4.2

Environment ............................................................................................................... 7

2.4.3

System Electrical ........................................................................................................ 7

2.4.4

PSU Fan ..................................................................................................................... 7

2.4.5

Station Distance from the System .............................................................................. 7

2.4.6

DECT Base Station (GDC-600BE) ............................................................................. 8

2.4.7

CO Loop ..................................................................................................................... 8

2.4.8

Wireless DECT Terminal ............................................................................................ 8

2.4.9

MPB VOIP .................................................................................................................. 8

2.4.10

VOIP channels (VOIB) ............................................................................................... 9

2.4.11

Other System Specifications ...................................................................................... 9

2.5

System Capacity .................................................................................................. 10

2.5.1

System Maximum Call Capacity ............................................................................... 11

2.6

Installation Overview............................................................................................ 12

2.6.1

General Installation Procedure ................................................................................. 12

2.7

Types of Connectors............................................................................................ 12

2.8

Installation and Safety Precautions ..................................................................... 13

KSU Installation ........................................................................................... 15

3.1

BKSU Unpacking ................................................................................................. 15

3.2

EKSU Unpacking ................................................................................................. 16

3.3

KSU Diagram, Exterior and Dimension ................................................................ 17

3.4

Basic KSU Mounting ............................................................................................ 18

3.4.1

Rack Mounting ......................................................................................................... 18

3.4.2

Wall Mounting ........................................................................................................... 19

3.5

Expansion KSU Installation ................................................................................. 20

3.6

Power Supply Unit Wiring .................................................................................... 23

3.6.1

Frame Ground Connection ....................................................................................... 23

3.6.2

External Backup Battery Installation ......................................................................... 24

3.6.3

Power Supply Unit Replacement .............................................................................. 25

BOARD INSTALLATION ............................................................................. 26

Summary of Contents for eMG800






































































































Search results

Summary of Contents for eMG800

Reviews:

Related manuals for eMG800

Brands by name

Popular brands

iPECS eMG800, Hardware Description & Installation Manual

Search results

Summary of Contents for eMG800

Reviews:

Related manuals for eMG800

Brands by name

Popular brands