iPECS eMG800 Hardware Description & Installation Manual Download Page 100

Page: 100 / 101

iPECS eMG800
Hardware Description and Installation Manual

Issue 1.8

8 Open Source Software Notice

Open Source Software used in this product are listed as below.

You can obtain a copy of the Open Source Software License from Ericsson-LG Enterprise Web site,

http://www.ericssonlg-enterprise.com. Ericsson-LG Enterprise reserves the right to make changes at any time

without notice.

Open source SW

Open source SW License

u-boot

GNU General Public License (GPLv2)

linux kernel

GNU General Public License (GPLv2)

busybox

GNU General Public License (GPLv2)

openldap

OpenLDAP Public License. BSD style

openssl

OpenSSL License and the original SSLeay license

(BSD-style Open Source licenses)

Ericsson-LG Enterprise offers to provide you with open source code on CD-ROM for a charge covering the

cost of performing such distribution, such as the cost of media, shipping and handling upon e-mail request to

Ericsson-LG Enterprise at [email protected]

This offer is valid for a period of three (3) years from the date of the distribution of this product by Ericsson-LG

Enterprise.

Summary of Contents for eMG800






































































































Search results

Summary of Contents for eMG800

Reviews:

Related manuals for eMG800

Brands by name

Popular brands

iPECS eMG800, Hardware Description & Installation Manual

Search results

Summary of Contents for eMG800

Reviews:

Related manuals for eMG800

Brands by name

Popular brands