iPECS eMG800 Hardware Description & Installation Manual Download Page 89

Page: 89 / 101

iPECS eMG800
Hardware Description and Installation Manual

Issue 1.8

To install the button kit for the LIP-9048DSS

Prepare your LIP-9048DSS for connection depending on the type of LIP phone. The setting switches are

hidden on the back of right side of the LIP-9048 DSS. Before you begin, remove protective cover from the LIP-

9048 DSS.

Power Mode

The MODE switch is used to choose the power mode between Slave and Master.

Symbol

Mode

Description

Slave

LIP-9048DSS receives power from another DSS.

Master

48V

LIP-9048DSS provides power itself.

Protocol Type

The TYPE switch is used to choose a call protocol type between iPKTS and SIP.

Symbol

Mode

Description

iPKTS

iPKTS protocol type of communication supported.

SIP

SIP protocol type of communication supported.

PoE Class

The PoE (Power over Ethernet) Class is indicated the class of the Powered Device (PD), and CLASS switch is

used to select the PoE class. DSS module supports all 4 classes listed in below table.

Class

Power Ranges

Description

0.44W to 3.84W

-. One LIP-9048DSS or two LIP-9048DSS

3.84W to 6.49W

-. One LIP-9048DSS with a LIP-9020

-. Two LIP-9048DSS with a LIP-9020

6.49W to 12.95W

-. One LIP-9048DSS with a LIP-9030

-. Two LIP-9048DSS with a LIP-9030

-. One LIP-9048DSS with a LIP-9040

-. Two LIP-9048DSS with a LIP-9040

12.95W to 25.5W

-. One LIP-9048DSS with a LIP-9050

-. Two LIP-9048DSS with a LIP-9050

-. One LIP-9048DSS with a LIP-9071

-. Two LIP-9048DSS with a LIP-9071



The default switch position is '0'.



'0' means the power OFF status and it does not support PoE power.



'1' means the power ON status and it does support PoE power.

Summary of Contents for eMG800






































































































Search results

Summary of Contents for eMG800

Reviews:

Brands by name

Popular brands

iPECS eMG800, Hardware Description & Installation Manual

Search results

Summary of Contents for eMG800

Reviews:

Brands by name

Popular brands