Intel Ethernet 10G 2P X520 Adapter User Manual Download Page 146

Page: 146 / 153

Power Require-
ments

5.5 Watts (maximum) @ 3.3 V

10.1 Watts (maximum) @ 12 V

0.6 Watts @ 3.3 V (AUX),
6.3 Watts @ 1.2 V
(VCORE)

Dimensions

3.93 x 3.67 in.

4.3 x 3.7 in.

3.0 x 2.5 in.

Operating Tem-
perature

32 - 131 deg. F (0 - 55 deg. C)

32 - 131 deg. F (0 - 55
deg. C)

MTBF

68 years

65 years

147 years

Available
Speeds

2 ports at 10 Gbps/(2 ports at 1 Gbps, see
Intel® Ethernet Gigabit 4P X540/I350
rNDC)

2 ports at 10 Gbps/(2 ports at 1 Gbps, see
Intel® Ethernet Gigabit 4P X520/I350
rNDC)

10 Gbps/1 Gbps

Duplex Modes

Full only

Standards Con-
formance

IEEE 802.1p
IEEE 802.1Q
IEEE 802.3ac
IEEE 802.3ad
IEEE 802.3ae
IEEE 802.3x
ACPI v1.0
PCI Express 1.0a

IEEE 802.1p
IEEE 802.1Q
IEEE 802.3ac
IEEE 802.3ad
IEEE 802.3ap
IEEE 802.3x
ACPI v1.0
PCI Express 2.0

Regulatory and
Safety

Safety Compliance

UL 60950 Third Edition- CAN/CSA-C22.2 No.60950-00 (USA/Canada)

EN 60 950 (European Union)

IEC 60 950 (International)

EMC Compliance

FCC Part 15 - Radiated & Conducted Emissions (USA)

ICES-003 - Radiated & Conducted Emissions (Canada)

CISPR 22 - Radiated & Conducted Emissions (International)

EN55022-1998 - Radiated & Conducted Emissions (European Union)

EN55024 - 1998 - (Immunity) (European Union)

CE - EMC Directive (89/336/EEC) (European Union)

VCCI - Radiated & Conducted Emissions (Japan)

CNS13438 - Radiated & Conducted Emissions (Taiwan)

AS/NZS3548 - Radiated & Conducted Emissions (Australia/New Zealand)

MIC notice 1997-41, EMI and MIC notice 1997-42 - EMS (Korea)

Intel® Gigabit Network Adapter Specifications

Feature

Intel® PRO/1000 PT Server
Adapter and Intel®
PRO/1000 PT Dual Port
Server Adapter

Intel®
PRO/1000
PF Server
Adapter

Intel® Gigabit ET Dual Port
Server Adapter and Intel®
Gigabit ET Quad Port Server
Adapter

Intel® Gigabit 2P
I350-t Adapter and
Intel® Gigabit 4P
I350-t Adapter

Bus Connector

PCI Express 1.0a

PCI Express
1.0a

PCI Express 2.0

Bus Speed

PRO/1000 PT Server Adapter

PRO/1000 PT Dual Port Server
Adapter

: X4

Transmission
Mode/Connector

Twisted copper/RJ-45

SX Fiber
Optic/ LC

Twisted copper/RJ-45

Summary of Contents for Ethernet 10G 2P X520 Adapter


























































































































































Search results

Summary of Contents for Ethernet 10G 2P X520 Adapter

Reviews:

Related manuals for Ethernet 10G 2P X520 Adapter

Brands by name

Popular brands

Intel Ethernet 10G 2P X520 Adapter, User Manual

Search results

Summary of Contents for Ethernet 10G 2P X520 Adapter

Reviews:

Related manuals for Ethernet 10G 2P X520 Adapter

Brands by name

Popular brands