Intel Ethernet 10G 2P X520 Adapter User Manual Download Page 134

Page: 134 / 153

Regulatory

10 Gigabit Network Adapter Regulatory Compliance

The following products comply with

Class A regulatory statements

for 10 Gigabit Ethernet.

Intel® 10 Gigabit AT Server Adapter

Intel® Ethernet X520 10GbE Dual Port KX4-KR Mezz, Model E90205

Intel® Ethernet X520 10GbE Dual Port KX4 Mezz, Model E62950

Intel® Ethernet 10G 2P X540-t Adapter, Model G16808

Intel® Ethernet 10G 4P X540/I350 rNDC

Intel® Ethernet 10G 4P X520/I350 rNDC

Intel® Ethernet 10G 2P X520-k bNDC, Model G33431

The following products comply with

Class B regulatory statements

for 10 Gigabit Ethernet.

Intel® 10 Gigabit XF SR Server Adapter

Intel® 10 Gigabit AF DA Dual Port Server Adapter

Intel® Ethernet Server Adapter X520-T2, Model E76983

Intel® Ethernet 10G 2P X520 Adapter, Model G28429

Gigabit Network Adapter Regulatory Compliance

The following products comply with

Class A regulatory statements

for Gigabit Ethernet.

Intel® ET Quad Port Mezzanine Card, Model E62937

Intel® Gigabit 4P I350-t rNDC, Model G10567

Intel® Gigabit 4P X540/I350 rNDC

Intel® Gigabit 4P X520/I350 rNDC

Intel® Gigabit 4P I350-t Mezz, Model G27582

Intel® Gigabit 4P I350 bNDC

The following products comply with

Class B regulatory statements

for Gigabit Ethernet.

Intel® ET Dual Port Server Adapter

Intel® ET Quad Port Server Adapter

Intel® PRO/1000 PT Server Adapter

Intel® PRO/1000 PT Dual Port Server Adapter

Intel® PRO/1000 PF Server Adapter

Intel® Gigabit 2P I350-t Adapter, Model G13021

Intel® Gigabit 4P I350-t Adapter, Model G13021

Regulatory Class A

Regulatory Compliance Statements for Class A Products

10 Gigabit Ethernet Products

Intel® 10 Gigabit AT Server Adapter, type EXPX9501AT (D80259)

Intel® Ethernet Server Adapter X520-T2, Model E76983

Intel® Ethernet X520 10GbE Dual Port KX4-KR Mezz, Model E90205

Intel® Ethernet X520 10GbE Dual Port KX4 Mezz, Model E62950

Intel® Ethernet 10G 2P X540-t Adapter, Model G16808

Summary of Contents for Ethernet 10G 2P X520 Adapter


























































































































































Search results

Summary of Contents for Ethernet 10G 2P X520 Adapter

Reviews:

Related manuals for Ethernet 10G 2P X520 Adapter

Brands by name

Popular brands

Intel Ethernet 10G 2P X520 Adapter, User Manual

Search results

Summary of Contents for Ethernet 10G 2P X520 Adapter

Reviews:

Related manuals for Ethernet 10G 2P X520 Adapter

Brands by name

Popular brands