Intel Ethernet 10G 2P X520 Adapter User Manual Download Page 142

Page: 142 / 153

Adapter Specifications

Intel® 10 Gigabit Network Adapter Specifications

Feature

Intel® Ethernet 10G 2P
X540-t Adapter

Intel® Ethernet 10G 2P X520
Adapter

Intel® Ethernet Server
Adapter X520-T2

Bus Connector

PCI Express 2.0

Bus Speed

Transmission
Mode/Connector

10GBase-T/RJ-45

Twinaxial copper/SFP+

10GBase-T/RJ-45

Cabling

10GBase-T (Category 6A)

10 Gigabit Ethernet over SFP+ Direct
Attach Copper (Cu)

10GBase-T (Category 6A)

Power
Requirements

15 W Maximum @ +12 V

6.2 W Maximum @ +3.3 V

25 W Maximum @ +12 V

Dimensions

(excluding bracket)

5.7 x 2.7 in
14.5 x 6.9 cm

6.59 x 2.71 in
16.7 x 6.9 cm

Operating
Temperature

32 - 131 deg. F
(0 - 55 deg. C)

MTBF

108 years

83.9 years

83.15 years

Available Speeds

10 Gbps/1 Gbps

Duplex Modes

Full only

Indicator Lights

Two per port:

Link and Activity

Two per port:

Link and Activity

Link
Activity

Standards
Conformance

IEEE 802.1p
IEEE 802.1Q
IEEE 802.3an
IEEE 802.3ac
IEEE 802.3ad
IEEE 802.3an
IEEE 802.3x
ACPI v1.0
PCI Express 2.0

IEEE 802.1p
IEEE 802.1Q
IEEE 802.3an
IEEE 802.3ac
IEEE 802.3ad
IEEE 802.3x
ACPI v1.0
PCI Express 2.0

IEEE 802.1p
    IEEE 802.1Q
    IEEE 802.1ae
    IEEE 802.3ac
    IEEE 802.3ad
    IEEE 802.3an
    IEEE 802.3x
    ACPI v1.0
    PCI Express 2.0

Regulatory and
Safety

Safety Compliance

UL 60950 Third Edition- CAN/CSA-C22.2 No.60950-00 (USA/Canada)

EN 60 950 (European Union)

IEC 60 950 (International)

EMC Compliance

FCC Part 15 - Radiated & Conducted Emissions (USA)

ICES-003 - Radiated & Conducted Emissions (Canada)

CISPR 22 - Radiated & Conducted Emissions (International)

EN55022-1998 - Radiated & Conducted Emissions (European Union)

EN55024 - 1998 - (Immunity) (European Union)

CE - EMC Directive (89/336/EEC) (European Union)

VCCI - Radiated & Conducted Emissions (Japan)

CNS13438 - Radiated & Conducted Emissions (Taiwan)

AS/NZS3548 - Radiated & Conducted Emissions (Australia/New Zealand)

MIC notice 1997-41, EMI and MIC notice 1997-42 - EMS (Korea)

Summary of Contents for Ethernet 10G 2P X520 Adapter


























































































































































Search results

Summary of Contents for Ethernet 10G 2P X520 Adapter

Reviews:

Related manuals for Ethernet 10G 2P X520 Adapter

Brands by name

Popular brands

Intel Ethernet 10G 2P X520 Adapter, User Manual

Search results

Summary of Contents for Ethernet 10G 2P X520 Adapter

Reviews:

Related manuals for Ethernet 10G 2P X520 Adapter

Brands by name

Popular brands