Intel Ethernet 10G 2P X520 Adapter User Manual Download Page 127 | Manualshive

Page: 127 / 153

background image

Event
ID

Message

Severity

53

Jumbo Frames cannot be configured when MACSec is enabled.

NOTE:

This message is used only for the following adapters:

l

Intel® Gigabit 2P I350-t Adapter

l

Intel® Gigabit 4P I350-t Adapter

l

Intel® Gigabit 4P I350-t rNDC

l

Intel® Gigabit 4P I350-t Mezz

l

Intel® Gigabit 2P I350 LOM

l

Intel® Gigabit 2P I350-t LOM

Informational

54

PROBLEM: A malicious VF driver has been detected.

Warning

55

The value of NumVFs exceeds the maximum value allowed by the driver in the current con-
figuration. The value will be set to the maximum allowed.

Informational

Below is a list of Intel network adapter custom event messages that appear in the Windows Event Log for the Intel 10
Gigabit adapters:

Event
ID

Message

Severity

6

PROBLEM: Unable to allocate the map registers necessary for operation.
ACTION: Reduce the number of transmit descriptors and restart.

Error

7

PROBLEM: Could not assign an interrupt for the network adapter.
ACTION: Try another PCI slot.
ACTION: Install the latest driver from

http://www.in-

tel.com/support/go/network/adapter/home.htm

.

Error

23

PROBLEM: The EEPROM on the network adapter may be corrupt.
ACTION: Visit the support web site at

http://www.in-

tel.com/support/go/network/adapter/home.htm

for assistance for assistance.

Error

24

PROBLEM: Unable to start the network adapter.
ACTION: Install the latest driver from

http://www.in-

tel.com/support/go/network/adapter/home.htm

.

Error

25

PROBLEM: The MAC address on the network adapter is invalid.
ACTION: Visit

http://www.intel.com/support/go/network/adapter/home.htm

for assistance.

Error

27

Link has been disconnected.

Warning

30

PROBLEM: The network adapter is configured for auto-negotiation but the link partner is not.
This may result in a duplex mismatch.
ACTION: Configure the link partner for auto-negotiation.

Warning

31

Network link has been established at 10Gbps full duplex.

Informational

32

Network link has been established at 1Gbps full duplex.

Informational

33

Network link has been established at 100Mbps full duplex.

Informational

34

Network link has been established at 100Mbps half duplex.

Informational

35

Network link has been established at 10Mbps full duplex.

Informational

36

Network link has been established at 10Mbps half duplex.

Informational

37

PROBLEM: PCI Express bandwidth available for this adapter is not sufficient for optimal per-
formance.
ACTION: Move the adapter to a x8 PCI Express slot.

Warning

«
...
125
126
127
128
129
...
»

Summary of Contents for Ethernet 10G 2P X520 Adapter


























































































































































Reviews:

No comments

Related manuals for Ethernet 10G 2P X520 Adapter

BL-PA300KTA - High Definition Power Line Communication Ethernet Adaptor...

Brand: Panasonic Pages: 64

Brand: D-Link Pages: 1

Brand: König Electronic Pages: 25

Brand: PATONA Pages: 14

Brand: Davis Instruments Pages: 4

Brand: Mini Gadgets Pages: 5

Brand: ViewSonic Pages: 69

ExpressSAS R380

Brand: ATTO Technology Pages: 2

Brand: NETGEAR Pages: 2

Brand: Manhattan Pages: 2

Brand: TP-Link Pages: 2

Brand: ACTiSYS Pages: 17

Brand: StarTech.com Pages: 2

W-70W Automatic

Brand: NGS Pages: 40

Brand: Logitech Pages: 143

Kit WI - Knx 2.0

Brand: RDZ Pages: 36

Brand: Pioneer Pages: 4

Brand: Pioneer Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands