Intel Ethernet 10G 2P X520 Adapter User Manual Download Page 130

Page: 130 / 153

Event
ID

Message

Severity

Team #<ID>: An adapter has re-established link. Network connection has been restored.

Informational

Preferred primary adapter has been detected: <member description>

Informational

Preferred secondary adapter has been detected: <member description>

Informational

Preferred primary adapter took over: <member description>

Informational

Preferred secondary adapter took over: <member description>

Informational

Primary Adapter does not sense any Probes: <member description>. Possible reason: par-
titioned Team.

Warning

Team #<ID>: A Virtual Adapter failed to initialize.

Error

An illegal loopback situation has occurred on the adapter in device <member description>.
Check the configuration to verify that all the adapters in the team are connected to 802.3ad
compliant switch ports.

Warning

Initializing Team #<ID> with <missing #> missing adapters. Check the configuration to verify
that all the adapters are present and functioning.

Warning

Virtual adapter for <VLAN name> [VID=<VLAN ID>] removed from team #<team ID>.

Informational

Adapter removed from team #<ID>.

Informational

You may not be able to change the virtual adapter settings. To resolve, reload the driver.

Warning

Virtual adapter unload process may have not completed successfully. Driver may not be
unloaded. To resolve, reboot the system.

Warning

Summary of Contents for Ethernet 10G 2P X520 Adapter


























































































































































Search results

Summary of Contents for Ethernet 10G 2P X520 Adapter

Reviews:

Related manuals for Ethernet 10G 2P X520 Adapter

Brands by name

Popular brands

Intel Ethernet 10G 2P X520 Adapter, User Manual

Search results

Summary of Contents for Ethernet 10G 2P X520 Adapter

Reviews:

Related manuals for Ethernet 10G 2P X520 Adapter

Brands by name

Popular brands