Intel Ethernet 10G 2P X520 Adapter User Manual Download Page 4

Page: 4 / 153

System Requirements

Hardware Compatibility

Before installing the adapter, check your system for the following minimum configuration requirements:

IA-32-based (32-bit x86 compatible)

One open PCI Express* slot (v1.0a or newer) operating at 1x, 4x, 8x, or 16x.

The latest BIOS for your system

Supported operating system environments: see

Installing Network Drivers

Supported Operating Systems

32-bit Operating Systems

Basic software and drivers are supported on the following operating systems:

Microsoft Windows Server 2008

64-bit Operating Systems

Software and drivers are supported on the following 64-bit operating systems:

Microsoft Windows Server 2012

Microsoft Windows Server 2008

RHEL 6.5

SLES 11 SP3

Cabling Requirements

Intel Gigabit Adapters

1000BASE-SX on 850 nanometer optical fiber:

Utilizing 50 micron multimode, length is 550 meters max.

Utilizing 62.5 micron multimode, length is 275 meters max.

1000BASE-T or 100BASE-TX on Category 5 or Category 5e wiring, twisted 4-pair copper:

Make sure you use Category 5 cabling that complies with the TIA-568 wiring specification. For more
information on this specification, see the Telecommunications Industry Association's web site:

www.-

tiaonline.org

Length is 100 meters max.

Category 3 wiring supports only 10 Mbps.

Intel 10 Gigabit Adapters

10GBASE-SR/LC on 850 nanometer optical fiber:

Utilizing 50 micron multimode, length is 300 meters max.

Utilizing 62.5 micron multimode, length is 33 meters max.

10GBASE-T on Category 6, Category 6a, or Category 7 wiring, twisted 4-pair copper:

Length is 55 meters max for Category 6.

Length is 100 meters max for Category 6a.

Length is 100 meters max for Category 7.

10 Gigabit Ethernet over SFP+ Direct Attached Cable (Twinaxial)

Length is 10 meters max.

Summary of Contents for Ethernet 10G 2P X520 Adapter


























































































































































Search results

Summary of Contents for Ethernet 10G 2P X520 Adapter

Reviews:

Related manuals for Ethernet 10G 2P X520 Adapter

Brands by name

Popular brands

Intel Ethernet 10G 2P X520 Adapter, User Manual

Search results

Summary of Contents for Ethernet 10G 2P X520 Adapter

Reviews:

Related manuals for Ethernet 10G 2P X520 Adapter

Brands by name

Popular brands