31
En
Note
• When Audyssey MultEQ
®
XT32 Room Correction and Speaker
Setup is complete, the “
Equalizer
” will be set to “
Audyssey
”
(
➔
56
). The
Audyssey
indicator will light (
➔
9
).
• You can cancel Audyssey MultEQ XT32 Room Correction and
Speaker Setup at any point in this procedure simply by discon-
necting the setup microphone.
• Do not connect or disconnect any speakers during
Audyssey MultEQ XT32 Room Correction and Speaker Setup.
• If the AV receiver is muted, it will be unmuted automatically
when Audyssey MultEQ XT32 Room Correction and Speaker
Setup starts.
• Changes to the room after Audyssey MultEQ XT32 Room Cor-
rection and Speaker Setup requires you run
Audyssey MultEQ XT32 Room Correction and Speaker Setup
again, as room EQ characteristics may have changed.
Error Messages
While Audyssey MultEQ XT32 Room Correction and
Speaker Setup is in progress, one of the error messages
below may appear.
The options are:
`
Retry
:
Try again.
`
Cancel
:
Cancel Audyssey MultEQ XT32 Room Correction
and Speaker Setup.
• Ambient noise is too high.
The background noise is too loud. Remove the source of
the noise and try again.
• Speaker Matching Error!
The number of speakers detected was different from
that of the first measurement. Check the speaker con-
nection.
• Writing Error!
This message appears if saving fails. Try saving again.
If this message appears after 2 or 3 attempts, contact the
dealer from whom you purchased this unit.
• Speaker Detect Error
This message appears if a speaker is not detected. “
No
”
means that no speaker was detected.
Tip
• See “Speaker Configuration” for appropriate settings (
➔
13
).
Changing the Speaker Settings Manually
You can manually make changes to the settings found dur-
ing Audyssey MultEQ XT32 Room Correction and
Speaker Setup.
See also:
• “Speaker Configuration” (
➔
54
)
• “Speaker Distance” (
➔
55
)
• “Level Calibration” (
➔
56
)
• “Equalizer Settings” (
➔
56
)
Note
• Please note that THX recommends any THX main speakers be
set to “
80Hz(THX)
”. If you set up your speakers using
Audyssey MultEQ XT32
Room Correction and Speaker
Setup, please make sure manually that any THX speakers are set
to 80 Hz (THX) crossover (
➔
54
).
• Sometimes due to the electrical complexities of subwoofers and
the interaction with the room, THX recommends setting the level
and the distance of the subwoofer manually.
• Sometimes due to interaction with the room, you may notice
irregular results when setting the level and/or distance of the
main speakers. If this happens, THX recommends setting them
manually.
Using a Powered Subwoofer
If you’re using a powered subwoofer and it outputs very
low-frequency sound at a low volume level, it may not be
detected by Audyssey MultEQ XT32 Room Correction
and Speaker Setup.
If the “
Subwoofer
” appears on the “
Review Speaker
Configuration
” screen as “
No
”, increase the subwoofer’s
volume to the half-way point, set it to its highest crossover
frequency, and then try running Audyssey MultEQ XT32
Room Correction and Speaker Setup again. Note that if
the volume is set too high and the sound distorts, detection
issues may occur, so use an appropriate volume level. If
the subwoofer has a low-pass filter switch, set it to Off or
Direct. Refer to your subwoofer’s instruction manual for
details.
Note
• You can view the calculated settings for the speaker con-
figuration, speaker distances, and speaker levels by using
e
/
r
.
9
Disconnect the speaker setup microphone.
Ambient noise is too high.
Retry
Cancel
MultEQ XT32: Auto Setup
Error message
Summary of Contents for DTR-70.2
Page 1: ...AV Receiver DTR 80 2 DTR 70 2 Instruction Manual ...
Page 122: ...122 En Memo ...
Page 123: ...123 En Memo ...
