119
En
The AV receiver allows you to update firmware using a
USB storage device.
*
In this procedure, on-screen display may vary depending on the
model.
Note
• Make sure your AV receiver and TV are turned on.
• Never unplug or turn off the AV receiver during updating pro-
cess.
• Never plug or unplug an HDMI cable and a USB device during
updating process.
• Never unplug the USB mass storage device and the power cord
during updating process.
• Do not access the AV receiver from PC during updating process.
• It will take about 60 minutes to update the firmware.
• The AV receiver will retain all your settings after update is fin-
ished.
Before you start
• Check “
HDMI Control(RIHD)
” setting (
➔
68
). The
update may not be successful if this setting is on.
• Turn off the controller device connected via RS232C and
via Ethernet network.
• Turn off Zone 2, Zone 3 and Zone 4.
• Stop playback of content from Internet Radio, iPod,
USB or Servers, etc.
■
How to turn off RIHD
Update procedure
Updating the Firmware via USB
1
In the Main menu select “Hardware Setup”.
2
Select “HDMI”.
3
Set “HDMI Control(RIHD)” to “Off”.
1
Connect a USB storage device to your PC. If
there is any data in the USB storage, remove it.
2
Download the firmware file from the Integra
web site. The file name is as follows:
ONKAVR0001_*******.zip
Unzip the downloaded file. The following three
files are created:
ONKAVR0001_*******.of1
ONKAVR0001_*******.of2
ONKAVR0001_*******.of3
3
Copy the extracted files to the USB storage
device. Be careful not to copy the zip file.
4
Remove the USB storage device from your PC
and connect it to the
USB
port on the AV
receiver.
When the AV receiver has two USB ports, you can
use either one.
5
Make sure the AV receiver and TV are turned
on.
If the AV receiver is in standby mode, press
On/Standby
on the AV receiver to light up the
front display.
6
Select the USB input source.
“
Now Initializing
” is displayed on the front dis-
play and then the name of the USB storage device
is displayed. It will take 20 to 30 seconds to recog-
nize the USB storage device.
7
Press
Receiver
followed by
Setup
on the
remote controller.
Main menu will be displayed on TV screen. Pro-
cedures thereafter can also be performed on the
AV receiver by using its
Setup
, arrow, and
Enter
buttons.
8
Go to “Hardware Setup” menu.
9
Go to “Firmware Update” menu.
10
Select “Via USB” and press
Enter
.
11
Select “Update” and press
Enter
.
Updating will begin.
As the updating progresses, the TV screen may
disappear depending on the program updated. In
this case, you can see the update progress on the
front display of the AV receiver. The TV screen
will reappear when you finish the update and turn
on the AV receiver.
Do not turn off the AV receiver and do not remove
the USB storage device during updating process.
12
Message “Complete!” appears on the front dis-
play of the AV receiver, indicating that the
update has been completed.
13
Using
On/Standby
on the front panel, turn off
the AV receiver and then remove the USB stor-
age device.
*
Do not use
ON
or
STANDBY
on the remote control-
ler.
14
Press
On/Standby
to turn on the AV receiver.
Congratulations!! Now you have the latest firm-
ware on your Integra AV receiver.
Summary of Contents for DTR-70.2
Page 1: ...AV Receiver DTR 80 2 DTR 70 2 Instruction Manual ...
Page 122: ...122 En Memo ...
Page 123: ...123 En Memo ...
