background image

SAFETY

11

SL, SM & SH 90, 110, 132, 150, 200, 250 &300 (50Hz)

L, H & HH 125, 150, 200, 250, 300, 350 & 400 (60Hz)

DANGER!

Hazard that 

WILL 

cause 

DEATH, SEVERE INJURY

 or substantial

property damage if ignored.  Instructions must be followed precisely to
avoid injury or death.

WARNING!

Hazard that 

CAN

 cause 

DEATH, SEVERE INJURY

 or substantial

property damage if ignored.  Instructions which must be followed
precisely to avoid injury or death.

CAUTIONS!

Cautions call attention to instructions which must be followed

precisely to avoid damaging the product, process or its surroundings.

NOTES

Notes are used for supplementary information.

BREATHING AIR PRECAUTION

Ingersoll–Rand air compressors are not designed, intended or

approved for breathing air. Compressed air should not be used for
breathing air applications unless treated in accordance with all
applicable codes and regulations.

General Information

Ensure that the operator reads and understands the decals and

consults the manuals before maintenance or operation.

Ensure that the Operation and Maintenance manual is not removed

permanently from the machine.

Ensure that maintenance personnel are adequately trained,

competent and have read the Maintenance Manuals.

Do not point air nozzles or sprayers toward anyone.

Compressed air and electricity can be dangerous. Before

undertaking any work on the compressor, ensure that the electrical
supply has been isolated and the compressor has been relieved of all
pressure.

Wear eye protection when operating or servicing compressor.

All persons positioned near to operating machinery should be

equipped with hearing protection and given instructions on its use in
accordance with workplace safety legislation.

Make sure that all protective covers are in place and that the

canopy/doors are closed during operation.

The specification of this machine is such that the machine is not

suitable for use in flammable gas risk areas.

Installation of this compressor must be in accordance with

recognised electrical codes and any local Health and Safety Codes.

The use of plastic bowls on line filters can be hazardous. Their

safety can be affected by either synthetic lubricants, or the additives
used in mineral oils. Ingersoll –Rand recommends that only filters with
metal bowls should be used on a pressurised system.

Compressed air

Compressed air can be dangerous if incorrectly handled. Before

doing any work on the unit, ensure that all pressure is vented from the
system and that the machine cannot be started accidentally.

WARNING

Imposing a normal or emergency stop on the compressor will

only relieve pressure upstream of the discharge check valve.

If maintenance work is required downstream of this valve, ensure

that all pressure is relieved at the process vent point external to

the compressor.

Ensure that the machine is operating at the rated pressure and that

the rated pressure is known to all relevant personnel.

All air pressure equipment installed in or connected to the machine

must have safe working pressure ratings of at least the machine rated
pressure.

If more than one compressor is connected to one common

downstream plant, effective isolation valves must be fitted and
controlled by work procedures, so that one machine cannot
accidentaly be pressurised / over pressurised by another.

Compressed air must not be used for a direct feed to any form of

breathing apparatus or mask.

If the discharged air is to be ultimately released into a confined

space, adequate ventilation must be provided.

When using compressed air always use appropriate personal

protective equipment.

All pressure containing parts, especially flexible hoses and their

couplings, must be regularly inspected, be free from defects and be
replaced according to the Manual instructions.

Avoid bodily contact with compressed air.

All safety valves must be checked periodically  for correct operation.

Do not over–pressurize the receiver tank or similar vessels beyond

design limits.

Do not use a receiver tank or similar vessels that fail to meet the

design requirements of the compressor. Contact your distributor for
assistance.

Do not drill into, weld or otherwise alter the receiver tank or similar

vessels.

Materials

The following substances are used in the manufacture of this

machine and may be hazardous to health if used incorrectly:
.

preservative grease

.

rust preventative

.

compressor coolant

For further information, consult Material Data Sheet 80440043

(LUBE OIL)

AVOID INGESTION, SKIN CONTACT AND INHALATION OF

FUMES

Transport

When loading or transporting machines ensure that the specified

lifting and tie down points are used.

Lifting equipment must be properly rated for the weight of the

compressor.

Do not work on or walk under the compressor while it is suspended.

Electrical

Keep all parts of the body and any hand–held tools or other

conductive objects, away from exposed live parts of the compressor
electrical system. Maintain dry footing, stand on insulating surfaces
and do not contact any other portion of the compressor when making
adjustments or repairs to exposed live parts of the compressor
electrical system.

WARNING

Any electrical connections or adjustments should only be

made by a suitably qualified electrician

 

Close and lock all access doors when the compressor is left

unattended.

Do not use extinguishers intended for Class A or Class B fires on

electrical fires. Use only extinguishers suitable for class BC or class
ABC fires.

Attempt repairs only in clean, dry, well lighted and ventilated areas.

Connect the compressor only to electrical systems that are

compatible with its electrical characteristics and that are within it’s rated
capacity.

Summary of Contents for Sierra H 125









































































Reviews: