Illustra IFS03B1BNWIT Installation And Configuration Manual Download Page 24

Page: 24 / 139

Illustra Flex Series Installation and Configuration Guide

8200-1456-01 D0

Figure 24 Adjusting the position of the camera

NOTE

For outdoor Dome camera series:
Users can adjust zoom level and focus level using the Illustra Connect Web User
Interface. Refer to Adjust Camera Focus / Zoom on page 59 for more information.

- End -

Procedure 11 Locking the Camera

Step Action

Use a soft, lint-free cloth to wipe the dome cover and remove fingerprints.

Attach the inner liner and camera housing.

Turn the power on after you have install the unit.

- End -

Procedure 12 Applying the desiccant

Step Action

Remove the papers from the back of the desiccant.

Attach to the interior side of the tilt adjuster as seen in the image below.

Figure 25 Location for desiccant application

Summary of Contents for IFS03B1BNWIT












































































































































Search results

Summary of Contents for IFS03B1BNWIT

Reviews:

Brands by name

Popular brands

Illustra IFS03B1BNWIT, Installation And Configuration Manual

Search results

Summary of Contents for IFS03B1BNWIT

Reviews:

Brands by name

Popular brands