Illustra IFS03B1BNWIT Installation And Configuration Manual Download Page 100

Page: 100 / 139

Illustra Flex Series Installation and Configuration Guide

8200-1456-01 D0

Network Menu

When you select the

Network

menu, the

TCP/IP

page displays, as seen in Figure 57 on page 94.

Figure 57 Network Menu

The Network Menu provides access to the following camera settings and functions:

• TCP/IP

• FTP

• SMTP

• SNTP

• CIFS

• Dynamic DNS

TCP/IP

Configure the IPv4 and IPv6 settings on the camera.

IPv4

Configure the IPv4 settings for the camera.

Note:

When you perform a factory reset or reboot the unit searches for the last known IP address. If

this is not available it reverts to the default IP address of 192.168.1.168. This could result duplicate
IP addresses. Refer to Network Menu on page 94 for more information.

Procedure 117 Configure the IPv4 Settings

Step Action

Summary of Contents for IFS03B1BNWIT












































































































































Search results

Summary of Contents for IFS03B1BNWIT

Reviews:

Brands by name

Popular brands

Illustra IFS03B1BNWIT, Installation And Configuration Manual

Search results

Summary of Contents for IFS03B1BNWIT

Reviews:

Brands by name

Popular brands