background image

4

 

Ideal Logic Code Combi - 

Installation and Servicing

gENERaL

Table 1 - general Data

Note. 

Gas consumption is calculated using a 

calorific value of 38.7 MJ/m

3

 (1038 Btu/ft

3

) gross 

or 34.9 MJ/m

(935 Btu/ft

3

) nett

To obtain the gas consumption at a different 

calorific value:

a.

 

For l/s

  

- divide the gross heat input 

(kW) by the gross C.V. of the gas (MJ/m

3

)

b.

 

For ft

3

/h

 - divide the gross heat input (Btu/h) 

by the gross C.V. of the gas (Btu/ft

3

c.

 

For m

3

/h

 - multiply l/s by 36

Key to symbols
gB 

=  United Kingdom 

IE 

= Ireland 

(Countries of destination)

pMs

 = Maximum operating pressure of water

C

13  

C

33 

C

53

 =  A room sealed appliance designed for connection via ducts to a 

horizontal or vertical terminal, which admits fresh air to the burner 

and discharges the products of combustion to the outside through 

orifices which, in this case, are concentric. The fan is up stream of 

the combustion chamber.

I

2h

 

= An appliance designed for use on 2nd Family gas, Group H only.

*  The value is used in the UK Government’s Standard Assessment Procedure (SAP) for energy rating of dwellings.  The test data from 

which it has been calculated have been certified by a notified body.

Ideal Logic Code Combi

26

33

38

Gas supply

2H - G20 - 20mbar

Gas Supply Connection

15mm copper compression

Injector Size

(mm)

4.15

4.65

4.9

Inlet Connection

DHW

15mm copper compression

Outlet Connection

DHW

15mm copper compression

Flow Connection

Central Heating

22mm copper compression

Return Connection

Central Heating

22mm copper compression

Flue Terminal Diameter

mm (in)

100 (4)

Average Flue Temp-Mass Flow Rate

(DHW)

30ºC 11g/s

32ºC 13g/s

35ºC 15g/s

Average Flue Temp-Mass Flow Rate

(CH)

63ºC 11g/s

68ºC 13g/s

73ºC 13g/s

Maximum Working Pressure (Sealed Systems)

bar (lb/in

2

)

2.5 (36.3)

Maximum Domestic Hot Water Inlet Pressure

bar (lb/in

2

)

10.0 (145)

Minimum Domestic Hot Water Inlet Pressure*

 bar (lb/in

2

)

1.0 (14.5)

1.3 (18.9)

1.6 (23.2)

Electrical Supply

230 V ~ 50 Hz.

Power Consumption

W

146 

 152 

177

Fuse Rating

External : 3A    Internal : T4H HRC  L250 V

Water content

CH litre (gal)

1.2  (0.26)

DHW litre (gal)

1.0 (0.22)

Packaged Weight

kg (lb)

41.3 (91.1)

41.4 (91.3)

41.6 (91.7)

Maximum Installation Weight

kg (lb)

35.9 (79.1)

36.0 (79.4)

36.2 (79.8)

Boiler Casing Size

Height mm (in)

830 (32.7)

Width mm (in)

395 (15.5)

Depth mm (in)

278 (11)

*Required for maximum flow rate. Boiler operates down to 2 l/min DHW delivery

 

** In areas of low water pressure the DHW restrictor can be removed

Maximum DHW Input :

26

33

38

Nett CV  kW

24.3

30.4

35.4

(Btu/h)

(82,900)

(103,600)

(120,900)

Gross CV  kW

27.0

33.7

39.3

(Btu/h)

(92,000)

(115,000)

(134,200)

Gas Consumption  l/s

0.698

0.871

1.016

(ft

3

/h)

(89)

(111)

(129)

Maximum

kW

26.1

32.7

38.2

DHW Output

(Btu/h)

89,100

111,600

130,300

DHW Flow Rate

l/min

10.7

13.4

15.7

at 35°C temp. rise

(gpm)

2.4

2.9

3.5

DHW Specific Rate

l/min

12.5

15.6

18.3

(gpm)

2.7

3.4

4.0

Table 2 - performance Data - Central heating 

Table 3 - performance Data - Domestic hot Water

Boiler Input:

Max.

Min.

26

33

38

Boiler Input ‘Q’

Nett CV kW

24.3

4.9

6.1

7.1

(Btu/h)

(82,900) (16,600)

(20,700) (24,200)

Gross CV kW

27.0

5.4

6.7

7.9

(Btu/h)

(92,000) (18,400)

(23,000)

(26,900)

Gas Consumption

l/s

0.698

0.139

0.173

0.204

(ft

3

/h)

(89)

(17.8)

(22)

(25.9)

Boiler Output:
Non Condensing

kW

24.2

4.8

6.1

7.1

70ºC Mean Water Temp.

(Btu/h)

(82,600) (16,500)

(20,700) (24,100)

Condensing

kW

25.6

5.1

6.4

7.5

40ºC Mean Water Temp.

(Btu/h)

(87,400)

(17,500)

(21,800)

(25,500)

Seasonal efficiency*

SEDBUK 2005

91%

91.1%

91%

SEDBUK 2009

89%

89%

88.9%

NOx Classification

CLASS 5

206279-1.indd   4

06/01/2011   09:09:32

Summary of Contents for LOGIC Code Combi 26

































































Reviews: