![background image](http://html.mh-extra.com/html/icom/ic-7600/ic-7600_instruction-manual_612307035.webp)
26
2
INSTALLATION AND CONNECTIONS
2
■
Accessory socket information
ACC 1
PIN No.
NAME
DESCRIPTION
SPECIFICATIONS
1
2
3
4
5
6
7
8
1
RTTY
Controls RTTY keying
“High” level
“Low” level
Output current
: More than 2.4 V
: Less than 0.6 V
: Less than 2 mA
2
GND
Connects to ground.
Connected in parallel with ACC 2 pin 2.
3
SEND*
Input/output pin.
Connected in par-
allel with ACC 2
pin 3.
An external equip-
ment controls the
transceiver.
When this pin goes
low, the transceiv-
er transmits.
Input voltage (TX)
Input voltage (RX)
Current flow
: 2.0 V to 20.0 V
: –0.5 V to 0.8 V
: Max. 20 mA
The pin outputs
a low level
signal when
the transceiver
transmits.
Output voltage (TX)
Current flow
: Less than 0.1 V
: Max. 200 mA
4
MOD
Modulator input.
Connects to the internal modulator
circuit.
Input impedance
Output level
: 10 k
˘
: Approximately 100 mV rms
5
AF
AF detector output.
Fixed, regardless of [AF] position in
default settings. (see NOTE below)
Output impedance
Output level
: 4.7 k
˘
: 100–300 mV rms
6
SQLS
Squelch output.
Grounded when the squelch opens.
SQL open
SQL closed
: Less than 0.3 V/5 mA
: More than 6.0 V/100 µA
7
13.8 V
13.8 V output when power is ON.
Connected in parallel with ACC 2 pin
7.
Output current
: Max. 1 A
8
ALC
ALC voltage input.
Connected in parallel with ACC 2 pin
5.
Input impedance
Input level
: More than 10 k
˘
: –4 V to 0 V
NOTE: If the CW sidetone level limit or beep level limit is in use, the CW sidetone or beep tone decreases from
the fixed level when the [AF] control is rotated above a specified level. (p. 130)
ACC 2
PIN No.
NAME
DESCRIPTION
SPECIFICATIONS
1
2
3
4
5
6
7
1
8 V
Regulated 8 V output.
Output voltage
Output current
: 8.0 V ±0.3 V
: Less than 10 mA
2
GND
Same as ACC 1 pin 2.
3
SEND*
Same as ACC 1 pin 3.
4
BAND
Band voltage output.
(Varies with selected amateur band)
Output voltage
: 0 V to 8.0 V
5
ALC
Same as ACC 1 pin 8.
6
TRV
Activates [X-VERTER] input/output
when “HIGH” voltage is applied.
Input impedance
Input voltage
: More than 10 k
˘
: 2 V to 13.8 V
7
13.8 V
Same as ACC 1 pin 7.
*
When the SEND terminal controls the inductive load
(such as a relay), a counter-electromotive force can
cause the transceiver’s malfunction or damage. To
prevent this, we recommend adding a switching
diode, such as an “1SS133,” on the load side of the
circuit to the counter-electromotive force absorption.
When the diode is added, a switching delay of the
relay may occur. Be sure to check its switching
action before operation.
e
HSEND
i
13.8V
ACC
socket
Relay
Switching diode
To a non-Icom
linear amplifier
[Example]
Summary of Contents for IC-7600
