Icom IC-7600, Instruction Manual, Page: 179 / 196

12
13
170
SPECIFICATIONS AND OPTIONS
13
■
General
• Frequency coverage : (unit: MHz)
Receive
0.030–60.000*
1
*
2
Transmit
1.800–1.999*
2
, 3.500–3.999*
2
,
5.33050*
3
, 5.34650*
3
, 5.36650*
3
,
5.37150*
3
, 5.40350*
3
,
7.000–7.300*
2
, 10.100–10.150*
2
,
14.000–14.350*
2
, 18.068–18.168*
2
,
21.000–21.450*
2
, 24.890–24.990*
2
,
28.000–29.700*
2
, 50.000–54.000*
2
*
1
Some frequency bands are not guaranteed.
*
2 Depending on version.
*
3 USA version only.
• Mode : USB, LSB, CW, RTTY, PSK,
AM, FM
• No. of memory channels : 101
(99 regular, 2 scan edges)
• Antenna connector type : SO-239
×
2 and phono jack
(RCA, 50 ø impedance)
• Temperature range : 0˚C to +50˚C (+32˚F to +122˚F)
• Frequency stability : Less than ±0.5 ppm 5 minutes
after power ON.
(0˚C to +50˚C: +32˚F to +122˚F)
• Frequency resolution : 1 Hz
• Power supply : 13.8 V DC ±15%
(negative ground)
• Power consumption
Transmit
: Max. power 23 A
Receive : Standby 3.0 A
Max. audio 3.5 A
• Dimensions : 340(W)
×
116(H)
×
279.3(D) mm
(projections not included)
13
3
⁄
8
(W)
×
4
9
⁄
16
(H)
×
11(D) in
• Weight (approximately) : 10.0 kg (22 lb)
• ACC 1 connector
: 8-pin DIN connector
• ACC 2 connector : 7-pin DIN connector
• CI-V connector : 2-conductor 3.5 (d) mm (
1
⁄
8
″
)
• Display : 5.8-inch
(diagonal)
TFT color LCD
■
Transmitter
• Output power
(continuously adjustable)
SSB/CW/RTTY/FM : Less than 2 to 100 W
AM : Less than 1 to 30 W
• Modulation system
SSB
: Digital PSN modulation
AM : Digital Low power modulation
FM : Digital Phase modulation
• Spurious emission
HF bands
: Less than –50 dB
50 MHz ban : Less than –63 dB
• Carrier suppression : More than 40 dB
• Unwanted sideband : More than 55 dB
suppression\
• ∂ TX variable range : ±9.999 kHz
• Microphone connector : 8-pin connector
(600 ø )
• ELEC-KEY connector : 3-conductor 6.35(d) mm (
1
⁄
4
″
)
• KEY connector : 3-conductor 6.35(d) mm ( 1 ⁄
4
″
)
• SEND connector : Phono jack
(RCA)
• ALC connector : Phono jack
(RCA)
■
Receiver
• Receive system : Double superheterodyne
system
• Intermediate frequencies
1st
: 64.455 MHz
2n : 36 kHz
• Sensitivity (typical)
SSB, CW, RTTY
: 0.15 µV
(1.80–29.99 MHz)
*
1
(10 dB S/N) BW=2.4 kHz
0.12 µV
(50.0–54.0 MHz)
*
2
AM
(10 dB S/N)
: 6.3 µV
(0.1–1.799 MHz)
*
1
BW=6 kHz
2 µV
(1.80–29.99 MHz)
*
1
1.6 µV
(50.0–54.0 MHz)
*
2
FM
(12 dB SINAD)
: 0.5 µV
(28.0–29.99 MHz)
*
1
BW=15 kHz
0.3 µV
(50.0–54.0 MHz)
*
2
*
1
Pre-amp 1 is ON. *
2
Pre-amp 2 is ON.
• Squelch sensitivity
(Pre-amp: ON)
SSB : Less than 3.2 µV
FM : Less than 0.3 µV
• Selectivity (IF filter shape is set to SHARP.)
SSB (BW: 2.4 kHz)
: More than 2.4 kHz/–6 dB
Less than 3.8 kHz/–60 dB
CW (BW: 500 Hz) : More than 500 Hz/–6 dB
Less than 900 Hz/–60 dB
RTTY (BW: 350 Hz) : More than 350 Hz/–6 dB
Less than 650 Hz/–60 dB
AM (BW: 6 kHz) : More than 6.0 kHz/–6 dB
Less than 15.0 kHz/–60 dB
FM (BW: 15 kHz) : More than 12.0 kHz/–6 dB
Less than 20.0 kHz/–60 dB
• Spurious and image : More than 70 dB
rejection ratio
(except IF through on 50 MHz band)
• AF output power : More than 2.0 W at 10%
(at 13.8 V DC) distortion with an 8 ø load
• RIT variable range : ±9.999 kHz
• PHONES connector : 3-conductor 6.35 (d) mm (
1
⁄
4
″
)
• External SP connector : 2-conductor 3.5 (d) mm
( 1 ⁄
8
″
)/8 ø
• DSP ANF attenuation : More than 30 dB
(with 1 kHz single tone)
• DSP NR attenuation : More than 6 dB
(noise rejection in SSB)
■
Antenna tuner
• Matching impedance range
HF bands
: 16.7 to 150 ø unbalanced
(Less than VSWR 3:1)
50 MHz ban : 20 to 125 ø unbalanced
(Less than VSWR 2.5:1)
• Minimum operating input : 8 W (HF bands)
power 15 W (50MHz band)
• Tuning accuracy : VSWR 1.5:1 or less
• Insertion loss : Less than 1.0 dB
(after tuning at RF power 100W)
Spurious signals may be displayed on the spectrum scope screen
regardless of the transceiver’s state (Tx or Rx). They are generated
in the scope circuit. This does not indicate a transceiver malfunc-
tion.
All stated specifications are typical and subject to change without
notice or obligation.