![background image](http://html.mh-extra.com/html/icom/ic-7300/ic-7300_full-manual_612249007.webp)
vi
PRECAUTIONS
R
DANGER HIGH RF VOLTAGE! NEVER
touch an
antenna or antenna connector while transmitting. This could
cause an electrical shock or burn.
R
DANGER! NEVER
operate the transceiver near
unshielded electrical blasting caps or in an explosive
atmosphere. This could cause an explosion and death.
R
WARNING RF EXPOSURE!
This device emits Radio
Frequency (RF) energy. Extreme caution should be
observed when operating this device. If you have any
questions regarding RF exposure and safety standards
please refer to the Federal Communications Commission
Office of Engineering and Technology’s report on
Evaluating Compliance with FCC Guidelines for Human
Radio Frequency Electromagnetic Fields (OET Bulletin 65).
R
WARNING! NEVER
operate the transceiver with a
headset or other audio accessories at high volume levels. If
you experience a ringing in your ears,reduce the volume or
discontinue use.
R
WARNING! NEVER
apply AC power to the [DC13.8V]
socket on the transceiver rear panel. This could cause a fire
or damage the transceiver.
R
WARNING! NEVER
apply more than 16 V DC to the
[DC13.8V] socket on the transceiver rear panel. This could
cause a fire or damage the transceiver.
R
WARNING! NEVER
reverse the DC power cable
polarity. This could cause a fire or damage the transceiver.
R
WARNING! NEVER
remove the fuse holder on the DC
power cable. Excessive current caused by a short could
cause a fire or damage the transceiver.
R
WARNING! NEVER
let metal, wire or other objects
contact the inside of the transceiver, or make incorrect
contact with connectors on the rear panel. This could cause
an electric shock or damage the transceiver.
R
WARNING! NEVER
operate or touch the transceiver
with wet hands. This could cause an electric shock or
damage to the transceiver.
R
WARNING!
Immediately turn OFF the transceiver power
and remove the DC power cable from the transceiver if it
emits an abnormal odor, sound or smoke. Contact your
Icom dealer or distributor for advice.
R
WARNING! NEVER
put the transceiver on an unstable
place where the transceiver may suddenly move or fall.
This could cause an injury or damage the transceiver.
R
WARNING! NEVER
operate the transceiver during a
lightning storm. It may result in an electric shock, cause
a fire or damage the transceiver. Always disconnect the
power source and antenna before a storm.
CAUTION: NEVER
expose the transceiver to rain, snow or
any liquids.
CAUTION: NEVER
change the internal settings of the
transceiver. This could reduce transceiver performance
and/or damage to the transceiver. The transceiver warranty
does not cover any problems caused by unauthorized
internal adjustments.
CAUTION: NEVER
install or place the transceiver in a
place without adequate ventilation, or block any cooling
vents on the top, rear, sides or bottom of the transceiver.
Heat dissipation may be reduced and damage the
transceiver.
CAUTION: NEVER
use harsh solvents such as Benzine or
alcohol when cleaning, as they will damage the transceiver
surfaces.
CAUTION: NEVER
leave the transceiver in areas with
temperatures below –10°C (+14°F) or above +60°C
(+140°F) for mobile operations.
CAUTION: NEVER
place the transceiver in excessively
dusty environments. This could damage the transceiver.
DO NOT
place the transceiver against walls or putting
anything on top of the transceiver. This may overheat the
transceiver.
BE CAREFUL!
The Main unit will become hot when
operating the transceiver continuously for long periods of
time.
CAUTION:
If you use a linear amplifier, set the
transceiver’s RF output power to less than the linear
amplifier’s maximum input level, otherwise a high input
could damage the linear amplifier.
CAUTION:
Use only Icom supplied or optional
microphones. Other manufacturer’s microphones may have
different pin assignments, and could damage the connector
and/or the transceiver.
NEVER
leave the transceiver in an insecure place to avoid
use by unauthorized persons.
Turn OFF the transceiver’s power and/or disconnect the AC
power cable when you will not use the transceiver for a long
period of time.
Turn OFF the transceiver’s power and/or disconnect the DC
power cable when you will not use the transceiver for long
period of time.
The LCD display may have cosmetic imperfections
that appear as small dark or light spots. This is not a
malfunction or defect, but a normal characteristic of LCD
displays.
Previous view