Hyundai N5000 Page 56 Instruction Manual Download

Page: 56 / 76

Chapter

Chapter4

. Inverter Operation

Inverter Operation

N5000 INSTRUCTION MAN

N5000 INSTRUCTION MANUAL

UAL

4.3.16 Group C Screen 1

‘Group C Screen 1’ screen panel comes out when ‘C code’ button is touched in function selecting

menu. 8 digital input channels, which have their own specific functions, (1~8 channel) are

monitored in this screen panel. When the terminal has ‘ON’ value, green light is appears in the

sqare box beside the item name. When the terminal has ‘OFF’ value, green light is turned off

(black).

Figure 23 Group C screen 1

(1)

Digital Input 1: Inverter gets ‘RUN CMD’ (RUN) command from this digital input terminal when

REMOTE mode is selected (Set 1 in the ‘Group A screen1’).

Close: [green light] RUN.

Open: [no light] STOP.

(2)

Digital Input 2: Inverter gets ‘EMG SW’ (Emergency stop) command from this digital input

terminal.

Close: [green light] Emergency stop.

Open: [no light] no function.

(3)

Digital Input 3: Inverter gets ‘FLT RST’ (Flow Lookup Table Restore) command from this digital

input terminal. (Same function as ‘breakdown cancellation’ button on the operation controlling

screen panel (refer 4.3.5))

Close: [green light] Restore the system to normal state from the breakdown state.

Open: [no light] no function.

(4)

Digital Input 4: Inverter gets ‘VFD MODE’ command from this digital input terminal. Inverter is

operated in inverter running mode when accepting signal from digital input 4.

[referece 8]

Close: [green light] Inverter running mode.

Summary of Contents for N5000













































































Search results

Summary of Contents for N5000

Reviews:

Related manuals for N5000

Brands by name

Popular brands

Hyundai N5000, Instruction Manual

Search results

Summary of Contents for N5000

Reviews:

Related manuals for N5000

Brands by name

Popular brands