Hyundai N5000 Page 2 Instruction Manual Download

Page: 2 / 76

SAFETY PRECAUTIONS

N5000 INSTRUCTION MANUAL

Please read the following instructions and directions given in this manual before selecting,

operating, repairing and checking.

Please be advised regarding mechanical safety information, direction and etc before use.

There are two different instructions explained in this manual regarding (danger) and (caution).

DANGER

: If not avoided, either death or injuries will occur.

CAUTION

: If not avoided, either death or injuries will occur as well as property damage.

Also, Please be advised to read all instructions given in the caution manual as well as danger

manual. It is important to read all the instructions completely.

In the following instruction manual, please note the word “CAUTION”.

* Common Matter

• Due to high voltage consumption, this product can cause electric shocks and fire to the

body and machine. An expert in Installation, driving, control, maintence must operate this

product.

• In order to stop or inspect the machine, you must first cut the high voltage completely.

• Insulation must be ensured between N5000 and the test equipment before applying electric

current for the purpose of test.

A. Installation of System and Wiring

• You must close all the doors whenever moving the inverter panel or installation.

• This machine is not protected from flooding. Please keep this machine away from water

while keeping and moving.

• Avoid from anything inflammable. It may cause fire to the machine.

• Avoid electric wires, welding spark, metal or dust from entering the machine. It may cause

fire.

• Do not operate the damaged inverter further. It may cause further damage.

• Do not connect AC supply to the output terminal.

• Use a power cable and control cable in a proper form.

• Only an expert should do grounding operation for the inverter system based on the

electrical drawing.

• Check the terminal polarities and the terminal numbers.

• Check the connection for loose screws. Loose screws may cause fire to the machine.

• Use proper power cable, VCB and electric contactor. If not, it may cause fire to the machine

DANGER

CAUTION

Summary of Contents for N5000













































































Search results

Summary of Contents for N5000

Reviews:

Related manuals for N5000

Brands by name

Popular brands

Hyundai N5000, Instruction Manual

Search results

Summary of Contents for N5000

Reviews:

Related manuals for N5000

Brands by name

Popular brands